So since I can use the motor for both applications which would be better. Usi g a servo or a stepper. This is an industrial application and 100 percent duty but just spinning some shafts in a...
Type: Posts; User: tpsimer
So since I can use the motor for both applications which would be better. Usi g a servo or a stepper. This is an industrial application and 100 percent duty but just spinning some shafts in a...
I have a special application for a EDM machine. I have to spin both my part and the spindle and I need a separate drive to run the part. I am hoping to use a servo motor with one of the programmable...
I have to make electrodes for a EDM machine from copper. I will be turning these on a CNC lathe. What is the best insert to use. This has to be finished with a .0078 radius tool nose.
Thanks for any...
I have a machine that has run for about 12 years. My computer went out on about a year ago and I just now am replacing it and trying to get it going again. I am using a HP laptop that I have run this...
I have a machine that has run for about 12 years. My computer went out on about a year ago and I just now am replacing it and trying to get it going again. I am using a HP laptop that I have run this...
I am using the g210's. The motors are 5.5 amp
Good evening,
I have a router that has been running for about 12 years. A man helped me with the electronics and built the power supply that has been being used. I do believe the power supply has...
That I get. I told you first grade language. Sorry for being such a pain in the but and thank you
tony
remember i am a 1st grader. does that mean that i am putting 5volt into the 11,12,13,15 pins from the relay that the switch tripped?
IS THE INPUT TO PINS 10,11, 12, 13 AND 15 0 VOLT OR 5 VOLT.
I have the relay working when the limit is tripped. I just dont know what signal to send to the pins 11,12,13 or 15, Is one of these 5v and where does it go. the prox switches dont have a part number...
I have a router that went out on me a 6 months back. I wired it 12 years ago and when I have gotten around to working on it again I decided to use a breakout board instead of direct wiring to the 25...
I need to get a breakout board and I don't know which to get. I previously wired direct from the parallel port to the stepper drives and used linuxCNC, I now want to use Mach3 and want spindle...
If there is an easy way to check it with a meter I would rather do that. I dont want to cause any other problems. I would also like to check another one I was saving for a fourth axis but I suspect...
Is there a way to test a G201 drive. I need to know if one of mine is bad. I may have finally killed it after about 13 yrs.
Thanks,
Also is the g201x compatable with the other two I have on my...
Thank you very much.
Tony
I have a router with three 640oz inch 5.5A 3.5mh motors. this was not put together by me but I need a new power supply for it. I have 201 Gecko Drives. Can anyone tell me what power supply will work...
I have been doing this for 30 years and mostly just bumped machines occasionally but this caused the worst crash I have ever had. I know I won't do it again but someone else will.
Is there a parameter to set the Fanuc I controller to reset to the beginning of the program from Auto mode. My Doosan will only reset to the beginning of the program from edit and I would like to...
I have a lynx 200 and need to know the spindle draw tube thread size. The thru spindle is 2 5/8 diameter and I need to get an adaptor for a 3j collet chuck.
can anyone help please.
thanks
I have a lynx 200 and need to know the spindle draw tube thread size. The thru spindle is 2 5/8 diameter and I need to get an adaptor for a 3j collet chuck.
can anyone help please.
thanks
I have a part that my boss wants me to knurl. There are 5 each of 10 for now and thousands later. Specifications are as follows.
2.5 diameter with a hub turned down to 1" about .75 long. On the 2.5...
Just looked up the quick change chucks on youtube. Awesome suggestion. looking into the quick change tooling. Coromat Capto seems to be the option I can find.
thanks
Good Morning,
I am looking for a bullet point list of the best suggestion for reducing lathe set-up times. I have been programming and setting up lathes for many years and am now in a position that...
thanks for the link. If the library doesn't have it I will by both authors.
tony
Thank you for the time you have taken to answer my questions. This is exactly what I needed, just an example of what this would look like. Much shorter than writing it out longhand (which I did once...
With the fanuc 21t it uses 2 line program for cycles. In the first line is:
g74 R????. I think this is the amount to retract after it retracts the full programmed infeed. I have put this to 0 but...
Using the short feeds it seems to feed back and forth rather than using rapid moves to back off and move forward. It works well to break chips but slows the cutting path down by more than double the...
What is the best way to go about learning how to write programs using parametric programming. I have done a little reading since I posted and Lynch has written a book covering this. Is it any good?...
Is there a way to write a parametric program like a g71 roughing cycle that will feed forward rapid back a few thousandths, rapid to cutting position and feed, repeat.
We cut a lot of plastic and...