Search:

Well, its FIXED! it was my oversight, i swapped 2 of the 3 legs on the 3 phase input wiring and works perfectly. I really didn't think it would be critical matter on a dc machine, but now i know....

Which board contains is responsible for the tool change cycle? I've relpaced the software module and evidently that is not where the subroutine is stored... The machine is a Vmc-15 with 88HS control...

i found the diagram of the jumpers and x,y,z, and c (rigid tap card) are correct. it will allow me to travel the full distance in every axis including Z, which will stop at z+4.000 when jogging. ...

i recently bought a vmc15 and it is having a strange problem with tool change cycles. The z axis attempts to go z4.2 inches + and hits the hard stop. the CS position is correct and it has .053 inch...

ANY SIEMENS TECHS IN THE STL AREA? I need help! I have a hyundai hit 8g w/ 805 control, i was running just fine and powered it off for 2 days and fired it back on and i get error #3 (plc stop) and...

DOES ANYONE HAVE AN OPERATING SYSTEM I CAN DOWNLOAD, IDEALY WINDOWS OR LINUX BASED, IM DOING SOME REVERSE ENGINEERING ON A FEW OF THE INTERPOLATION SUBROUTINES FOR AN OPEN SOURCE CONTROLER PROJECT...

I HAVE AN IDENTICAL SETUP, THERE IS NO PROBLEM WITH THIS AT ALL, I JUST USED AN ADAPTER TO VGA AND PUT IT DIRECTLY TO A 12.1" LCD MONITOR, THERE ARE NO ISSUES WITH THIS SETUP EVEN WHEN THE MACHINE IS...

i have 2 parts i need quoted, material must be 4140 or a2 tool steel, 1 pc is 0.975 x 0.984 x 2.875 and the other is 0.340 x 2.650 . the mill part is +/-.005 with the exception of the counterbore...

try this, with the spindle on and at the desired depth give it a g13 (climb) or g12 (conventional) it works with haas and alot of various newer controls

Ex:

G0 X0. Y0.(CENTER OF HOLE TO BE...

basically to copy off the mill operating system. i have access to both usb equipt and floppy machines. i had a milltronics that i was able to copy off the actual operating system and it saved me big...

does anyone know where or how i can get a back-up of the haas operating system?

sorry the job is done, does anyone know how to delete these posts?

HI, I NEED 6X OF THE SAME PARTS MADE. MATERIAL IS 6061 ALUMINUM, TOLERANCES ARE TYPICALLY +-.005. I ATTACHED THE .DWG FILE FOR THIS PART. IF NEEDED I CAN SEND IN MASTERCAM FORMAT ALSO. PLEASE...

try www.automationdirect.com and look at the durapulse vfd. I just bought a 5hp vfd for my milltronics partner 4 and it was very straightforward to install. after tweaking the parameters to match...

you could interpolate it to about .003 undersize then ream it to size... although a reamer that size would cost quite a bit

does anyone know the final drive ratio on this machine in high gear? Im getting 32t on the motor, 28t on the driven... giving me a 1.14:1 ratio, is that it? is there any overdrive in the...

if you type in s500 m03 in mdi it will say to press cycle start , i do so and it will read 500 rpm (cw)... if you vary the % of spindle speed it reflects the changes for that too (ex. 500 rpm...

I tracked ALL the connections for the analog spindle and checked the continuity on all of them, everything checked out fine. Im beginning to suspect the spindle enable wire, could that possibly...

"If I remember right, the analog spindle signal (0-10v) comes from the card cage's MISC pin 13 and travels to PC-REL-1B(relay board). It comes out of the relay board at TB2-7 and goes to the spindle...

OK... now I have everything moving, the thing is that terminal 13 isn't getting any input voltage in the spindle inverter. it is suppose to get 0-10vdc, 10v being 200% 5v being 100% and 0v being...

Thanks for the file, it is VERY helpful, it turns out the errror clears and doesnt come back... the frequency(hertz) is set to zero aswell as the amperage. for some reason i cant get the display...

No, it looks just like this one on e-bay... heres the item #270297305621 . I'd like to get this thing going pretty soon, my work is getting rid of a fadal w/ full enclosure that is having problems...

Ok, i got the x, y, and z axis moving, got rid of the error codes(bad v and keyboard error) turns out the cable coming from the front panel to the card cage had a bad connection... but now i cant...

I just pulled off the front panel and checked the switches... Another post led me to check these. I found that the cycle start button doesnt get continuity on 1/2 of the switch... The switch was...

I think I bought this guys cnc, its a partner 4(iv) with centurion 5(V) having the same problems still. any ideas?? ive got the book coming from milltronis this week. please let me know!

I have also tried this, with the exception of running the home function, it doesnt allow any thing but the ESC key which doesnt seem to do anything.

I've tried this same thing but i'm not able to get anything to happen at all, it just keeps going to the main control screen... i think im just lost anymore... do you know where i could get a diagram...

Thats what I was thinking, it was just confusing when one of the guys was saying to replace a heat sink on the keyboard encoder board instead of replacing the whole thing which is big $$. I have...

I have done that as well, I get the exact same thing happening. Im nearly convinced that a relay could be at fault since the lights on the keypad on the controller and external keyboard flash on...

NEED HELP!! I just bought a 1991 Milltronics Partner 4 with Centurion 5 cnc control... It powers up but once it reads the memory it says "keyboard error" and about that time the lights on the...