Deleted
Type: Posts; User: L98FIERO
I have a Matsuura with a Yasnac MX3 control, it is the base control for the mid 80s Seikos controls and I am getting the 331 X axis fuse alarm, I can't find a fuse and the problem started as an...
My email is [email protected]
I need some help getting a parameter list and preferably more than one.
As most of you have probably found, there are few that will or even can help with the old Yasnac MX3 based Seicos control,...
Thank you, that's much more simple than deleting the offending parts!
Just takes time.Oddly the lines were projected to both sides of the disc so I manually editing out the original lines and text as well as the undesired parts and then used 3D engrave to generate the...
Ok, I figured out that I can project curves, the numbers have to be vectorized, but how do I then get rid of the original lines without deleting the lines on the part?
I'm trying to mark graduations on the bevelled edge of a disc? I'm making a degree vernier, how do I go about getting the lines on the bevel at the correct angle, the disc has a 60° bevel about .4...
Don't think so, those moves are a chamfer.
The weird part is it worked in a previous run and during setup and then the problems. If I remember correctly the only thing I changed after the setup...
I'm running a program that I've run previously but with different results. I'm turning a sleeved adapter, boring the ID then turning the OD, the boring works as it's supposed to but the OD turning...
I just sent a copy of the parameters from my machine, do you have the definitions for the parameters for the MX3 on my 510V? I'd be interested if you do.
I've deleted some screens on the simulation part and am looking for a way to get them back so I can save stl models, search function in the help isn't particularly useful.
Last I heard from Al, in V31 you can't and I just looked at the What's new in V32 and from what I saw, it posts the subprogram in absolute coordinates which is useless.
My issue it that the old...
Thanks Rob, tried it and it works, go figure! There's a lot in Bobcad and it's just not something I've used much before, 90% of what I do is 2½ axis.
That may have been the issue but from memory, it was a longer, about 1" travel, and I don't think there's that much lag in a Fanuc 0M. On the plus side, I only recall it having happened once and not...
No, not a G0 dog leg, it was at maximum feedrate, straight point to point path. I only recall it having happened once but it did happen, it was on a 2D open pocket where 2 sides were open.
I ended up just drawing a line at Z-.028 the appropriate length and copying in a circular array, did a simple 2D profile with no offsets and then manually editing the end depth of the path. Kind of...
With high speed adaptive roughing Bobcad should know if there is anything in the way BUT, I've had it clip corners while roughing, not a crash as such but I've had it take 0.01" off a corner at high...
I'm trying to mill 32 tapered slots in a circular pattern, they start approximately at x.188 z-.028 and end at x.320 z-.031 and I want to mill them with a 90° engraving cutter and repeated radially...
Does anyone have the parameters required to turn on some of the options on the YASNAC MX3 control? I have a Matsuura MC-510V and have contacted Matsuura who said it's no longer supported and that...
Changing download program solved the problem
I have a Matsuura MC-510V with the MX3 control with basic memory and have found a 256k board. There is the instructions online for replacing the memory with the 1M Memex board but is that what will...
Did you get the parameters? I, too have a 510V and the parameter list if you need it. PM me if you do.
I'm having some issues with downloads to the YASNAC MX3 control on my Matsuura 510V. This is the typical start of a program for me:
%
O200 (OFFSET FLANGE)
G17 G20 G40 G49 G80 G90
G00
G91 G28...
No one replied so......
It turns out the way to clear this is to turn the rotary switch on the top left of the MD20/MB21 main board to 1, it normally is at 0. I did it with the machine turned off,...
Anyone know how to clear this error?
On the Hellmans site they suggest changing parameter 6104 D6 to 0 but a decimal parameter and already 0
Not sure how it happened or what I did but I was trying...
Does anyone know the parameter to turn on the M8 (mist) option and the macro option? It's for a Matsuura MC-510V with a Yasnac MX-3 control. A options parameter list would be great if possible.
Making up a simple little program and got this error in simulation:
'MW_CC_STOP' is missing
Command:MW_CC_START MW_CC_CONTROL MW_CC_LEFT D0.000000000
I was milling a profile with Bobcad...
I have another question about my 'new to me' control.
The machine is set up to have metric as it's default units, what parameter changes that to Imperial(inch) and if that is changed, will it...
Rob, that looks really good but, where do the 'next_tool_with_prefix' and 'first_tool_with_prefix' come from? Is it from the BcCamPostExe program that will not run on my Windows 7 computer? Also, the...