Search:

The machine is a Alextech Viper 3000 YMS 2007modell

Need to know witch parameter to change so the controll let me operate the chuck in M0 mode.

Got a 2007 Alex-Tech Viper 3000 machine.

The spindle brake is acting up, and do not clamp as hard as I like it to.

As in, when I tighten tha jaws in the chuck the spindle brake cant hold the...

How do I set the tool offset on the secondary tool in a twin tool fixture if I cant Call up the tool data first?

How would the machine even know what tool is beeing used if they are both in T08.
...

Hi.

I got some problems With this to.

I have a Viper 3000 YMS With Fanuc 18i-TB controll With Manuell Guide i.

When I need to set the work cordinates in the sub spindle I belive I need...

Hi.


We have a Lathe (Alex-Tech Viper 3000 YMS) With the Fanuc 18i-TB controll.

I have problems With setting the tool data for double tool holders.

For the T0800 holder I use T0808 and...

Hi.

I migyt have been overthinking this a bit, but I cant get the machine set up with the right tool data and reference Points.

Machine: 2007 Alex-Teck Viper 3000 YMS

Controller: Fanuc...

Hi.

Thanks for the tips.

I will have a look at the input bits for the proximity switches today if I can find them.

Unfortunatly I do not have the electrical diagrams for the machine. Will...

I hve changed the proximity switches for the main spindle, but I do not know where to check the diagnostics for this controller.

Any tips?

Im currently moving the part manually from the main to sub spindle.

I also have trouble getting the coolant to stay on when running a program that starts with the sub spindle. It only throws out a...

Im currentle running a copy of a program already on the controller.


The sub spindle (w-axis) travels to the set point, clamps the part and the main spindle opens.

Then the spindles just keep...

I found it.

Was under settings, and pressing softkey right arrow and OPR to get in the menu.

Then it was just a matter of choosing CH1 and CH2 OD/ID

I cant figure out how to change between ID and OD clamping on this machine.

I have tried the M88/M89 commands after searching the forum, but theese are used with sub spindle orientation.

There...

Hi, I am in the need of a manual for the Cincinnati Milacron Lancer 1000.

Anyone?

Thanks.

My dyna2400 has a problem. Im running all the original setup.

And a relay inside the original "control panel" do not conect, it just tries to.

And its clicking about the frequense of the 50hz...

If anyone still wants to copy theire manuales they would be mostley welcome :)

I just got me an 2400 LIKE NEW

Maby I could help some, but are looking to find the manuales myself, I just got an partial complete one.

But still managed to program it some.

Nice conversiones guys.

Just got me a Dyna 2400 myself, in great working condition.

The machine has not been used enugh to wear out the 5mm end mill they put in it when it was new :) So the...

You should definitly try theese G codes, because in tapping cycles the spindle and z fedd are sync`ed.

With G01 they are NOT

Not sure what machines you are talking about, but probably okumas atleast :)

The Mazak lathe I used to operate could be converted to LCD with a kit provided by the dealer.

Were pretty...

If the thoothet belt jumped, the encoder for the z-axis should have shut the machine down right away. And the load are lower when the thread are so far done (85%) that the cutting forces shouldent...

I am currently hired in to get an 1982 Okuma LC20 up and running.

And need to get in to the parameters to switch of the parts counter, because I get alarm number 3900 when the program ends.

Do...

Replaced 3 capacitors and 2 fuses and its ALL GOOD :D

Just what I was hoping for, thank god the controlls and everything are ok.

In Norway we have 2 diferent types of 3phase current, 220v and 380v.

And if you conect the machines wrong you could be F#¤&%, if it were a 380v machine and conected to 220v if would be fine...

Bought a Ecoca EL6110E lathe with Mitsubishi Meldas 520l controlls.

The machine were marked with a machine sign saying that the input voltage should be 380v 3ph, just like we have where I live.
...

Ah, just too mention it, if you only change the diameter of the drill to the current diameter of the drill, but dont change the tool type to a drill, the machine thinks the drill size are the actual...

Sounds like the machine things youre drill are an internal turning tool, that exact thing happens when this is wrong in the tooldata 2

Also have you set the standard value for the drill holder?
...

I also need some downloads for the spindle and servo drives for tha mitsubishi controller, found these but could not download them.

Please help me out here guys, direct link anyone??

Thanks.

Thanks, but could not find the meldas 520l download.

Maby just me :)

Im getting my newest machine tomorrow, its a Ecoca EL-6110E with Mitsubishu Meldas 520 L control.

The lathe are a 500mm x 1000mm and have a 15kw main engine, chip convayor, manual chuck and 4...