Search:

Purchasing a used but in good condition F-M1 1997 with MSC-521 control. Currently has 32000 available characters for memory. Does anyone know the max memory that the control can be increased to?
...

Thank you for helping with the problem . The spring loaded damper seems to be functioning good. Depress and returns without a problem. But when the shop was off and quiet i looked into it a little...

The issue is intermittent. But a number of times when the carousel is returning to its parked position it will retract rather quickly and hit harder than it should.It does not occur when advancing to...

Hello
First time to running a Okuma cnc mill using the OSP700M control

First program very basic

N10 ( Okuma OSP700m)
N30 (O1.MIN 10/20/2016)
N60 (Tool No1.)
N20 G15 H01
N70 T01 M06

Can V27 with 3 axis pro create a thread mill program for a
1/8-27 npt internal thread using a thread mill ?

Thanks in advance for any help .

Good afternoon

I have a Arrow 500 with the Control Techniques
Control . Just had the z axis motor repaired ,
Brake was bad but resolver good . My tool change
Height number for the z axis is...

Give me a call same problems
413-329-1503
Mark

The battery light being on for 8 months should have
Been looked into when it first began . On a sl3
There are two batteries that need replacinglocated
In the back left cabinet . They keep the...

Looked in the service manual for sabre 750 cnc mills. They recommend MobilLux EP2 . Just so happens it was the same grease that a Oil tech at a local distributor suggested .He said if you are not...

Can any one help. I cannot find the layers anymore in the UCS windows ,how can i get it back?

When I create entities from a solid and , then go to measure one of the entities as I am clicking...

I have just installed V26 mill/pro and lathe. When I import a DWG file the physical size and associated dimensioning changes. In this case the part a 6.5 inch id cavity is now only measuring .238...

The control is the Acramatic 2100
serial # 7029-AOB-98-1553
Model # ERO
Control Design # 91203577

Thanks
Mark

Thanks
The problem is very intermittent. I started the machine and had the error right away. After letting the machine sit for 15 minutes or so the error could be cleared and the machine aligns no...

Does any one else experience a clunking, possibly transmission clunk when running g96? It happens when changing speeds after slowing down for a larger diameter and then spinning up again right before...

Ok
Thanks for your help. I will try their dnc software.

Mark

We have a sabre 750. Beginning of the week went to start the machine and during alignment developed this error. Axes drive foldback overload error. Stating that a axis is overloaded such as to heavy...

Hello thanks for the reply. But I have the Fanuc 3TF with color crt do you know if it is possible? I have them in my posted file but when I download all that is in its place is a comma.

Also are...

I have a SL-3H For the Zaxis gear box, turret, and way lube I use Vactra Oil#2
For the tailstock and transmission I use DTE OIL LIGHT

Hope this helps
Mark

Hello

Is the 3tF control capable of receiving a file with comments? I have them in my program but have never been able to have them come
over when sending the file to the machine by RS232.

Any...

Hello,
Can anyone help me with this error?
I have a Arrow 500 with the Control Techniques control ver 2.56 software. After two years of static ram file corrupt I reformatted drive C per...

Rob,
Wound up taking all the contents out of the MillSim
folder on my 64 bit laptop and copying them to the
32 bit machine and everything works fine after running
Through the setups as you...

Rob
Thanks for the reply.I took one of their acramatic mill posts and saved it out
as a arrow500.pst file. Is this where the problem has occured? When I post the toolpath it is using the post that...

Hello

When I try to run the toolpath verification this message appears when verify
starts to load. Does any one know what it means.

Thanks

Have successfully fired up a saber 750 with a A2100 control using flash memory module, which replaces the IDE hard drive. Ran all day yesterday without a problem. Have a edm tech that has been using...

Would anyone have a idea why when I first power up the mill the monitor does not come on. After shutting down and restarting the monitor comes on.This has happened at least 10 times so far and it...

Do not support directly under the spindle by means of placing the block of wood directly on the spindle nose, doing so you are putting pressure right on the bearings. Build up the wood right behind...

Machine was running fine Thursday. Yesterday machine fires but no monitor or
the nc side of the control does not come up. Machine can home,spindle works,
turret works but no screen,fapt, or nc....

Give me a call it is easier.

413-329-1503
Mark Reuss

UniversalFab are you speaking to facecutter?? I tried to contact him by PM and his message box is full. [email protected]

For starters what is your 3 phase supply voltage to the machine? 208-230-380-415-460. After knowing this you need to tap the transformer correctly based upon the incoming voltage. Be aware that the...