It's a hitachi seiki, not mori.
Is it a micon 8-1 0r 8-2?
Does the micon board have a ptcoda number or sqm8?
I have worked on a lot of hitachi may have what you need.
Type: Posts; User: jdeere4250
It's a hitachi seiki, not mori.
Is it a micon 8-1 0r 8-2?
Does the micon board have a ptcoda number or sqm8?
I have worked on a lot of hitachi may have what you need.
You can output the ladder by cable using rs232c.
I often did it, but never had to reload it this way.
The procedure is init pin to ground for 30 seconds.
Need help call me at 978-660-0332.
Yes, that what is frustrating about this, is, I am supposed to know.
What issue are you having?
What machine,? etc
I have quite a lot of exp.on fs10/11.
Need help loading pmc parameters using the hex looking backup.
Got the cnc side loaded from previous saved file.
Can't get the PC parameters to load.
Were saved recently by fanuc.
Since I...
This machine lost its memory.
Fanuc had made memory backup fairly recently.
Was able to reload cnc parameters.
But, pmc parameters are in the hex looking stuff.
And it says file error...
Fairly sure I saved all memory from one of these last year.
I can check monday.
Where are you located at?
Top board has problem
It is possible to deactivate fapt.
But software has to change.
And fanuc alphanumeric keypad as the addressing of keys are different.
Like for example the letter p might be g ore some such....
hey ray, your pms have pcmcia slots, look at your pic entitled servo and drives. the first and fourth units are the pmd s and have a little door on the unit this is where the card goes.
anothe thing...
ok, the real deal to backing up some of these koyo boyos is you need a from pcmcia card. do not , and i really mean it, use a flash ata card on these , it will fit, but damage the control.
you need...
HI all, we just purchased a older mori seiki AL2 AT.
The proble is we got no manuals at all.
What we need is the Ladder diagram for this machine.
We have a wiring diagram from other AL 2...
this is what you get when you clear memory, i am fairly sure that they were loading thu rs232, something happened awry like ps101. then to clear this memory got cleared. Hence 4x7 alarms and 100...
'course it can be done with right equip.
it a little old now.
need the pg mate.
needtoreloadmemory
Hi all, we have a Mori Seiki M25FH, Fanuc 18MA control lost all memory ( in transit) We could use some help. Thanks in advance.
i have parms for 600h , need to know control and serial of machine tool. and year
We have a Tape Drill Mate Model T, We are having 1008 and Ps 585 alaRMS.
Control is fanuc 0MB 1991 vintage.
It is giving us 1008 belt slip alarms. The turret is not binding, the belt is...
Is it 15A or 15B model ? 15A needs Passwords, to install the Options.
You are supposed to get them from Fanuc. Contact them first and try to get them.
do not touch the pots on the -0030 as they are orientation adj. if machine is doing good tool changes let them alone. this drive is as good a drive as you can get. the thing you need to change are...
i may have what u need . i worked on this machine about 2 years ago. i keep a copy of mem backup.I seem to remember that the rs232 would not wk from the cnc to laptop . but it did into cnc. so i may...
We have a Mori Seiki MV35/35. yasnac mx1 control
Here is the problem : It zeros out fine, jogs, manual is fine, no alarms.
If you command it in either MDI or Auto mode as soon as cycle start is...
Hold On! first which control ?
Then , are you sure you can access the parameter screen?
Next is the ram parity alarm constant?
what alarms exactly , numbers etc ?
Hello again, if this is not the exact configuration. It very close with the Yellow cassette.
I would really appreciate a copy of the CNC parameters and the PMC parameters.
I will tell the owner we...
do not reset the nc side parameters, as the fapt may as well be a different country as fat as the cnc is concerned.
It has a seperate battery backup cable, Resetting the cnc has no positive effect...
Hi there, I did find another VA55MK2 but I have not been able to travel to it yet. 3 hrs or so.
I would really appreciate some help.
This is for a friend that has a machine tool he bought from a...
Hi Bill, your are correct in your guess, the BMU was not in the machine when I got there, I can probably get it back though. Any suggestions?
Hi all, we have an Hitachi Seiki VA 55 MK2, Fanuc 11MF control, lost memory , no paperwork at all. We need CNC parameters, PMC parameters also possibly ATC macros.
check manual/absolute.