Search:

CncCodeMaker.
There will be a lot of people interested in your program at this Swedish forum.
look under "Mekatronik"
http://elektronikforumet.com/forum/
Best regards PerE

Try to switch the cables to the motor, red - black & black - red.
Hope this help you.

Why are you measure a 12DC with your multimeter in AC mode ?
That is wrong.
Best regards Per

It is thanks for you kreutz that i managed to do this. :cheers:
This is my first PCB that i ever made and i am 47 years old
Best regards:
Per

"Huston, we have contact"
Replacing the four caps from 10uF Tantalium to 1uF Electrolyt did it so i made contact with the UHU chip.
But there is only ~-6.5V from MAX232 to TL082 chip, could that be...

So Mr kreutz i should use 1uF Tantalium for the four caps C10,C11,C12 & C5 ?
I will replace them tomorrow and let you know if that was the problem.
Per

Ihave tantalums 10u in there.
I am no expert in electronics so be cind to me.
Is it good with electrolyts and shold i change only C10,C11,C12 & C5 or should i even change the 5 one below the four...

Thanks for your reply kreutz.
It is MAX232CPE chips with 10u caps around it.
I will change the caps (10u-0.1u) to se if that was the problem for me.
Best regards:
Per

Hello Micke.
If you want you can try to ask your questions in a Swedish forum, there are a lot of people who are using Mach3 there.
Me to.
http://elektronikforumet.com/forum/
Look under...

Hi.
I have finally assembled my old uhu board wich i had routed out from a blank pcb board.
I have failed to connect to the terminal, i have tried different computers and terminal program without...

hoss2006.
Is it possible that you can share your screen with all the scripts for us ?
I am very interested in your features to probe edge and holes.
Best regards:
Per

Yes, i have found them but i need them in another format eg G-code or Eagle files so i can handle them in a proper program and run it in Mach3.

Yes, on my router.

Hi there
I want to build this one but where can i find the PCB G-codes for the UHU servo card ?
Thanks i advance.
Per

Hi.
Would you like to share that postprocessor to me ?
Best regards: Per

Hello Micke.
Have you read this Swedish forum ?
http://elektronikforumet.com/forum/viewforum.php?f=5
Cheers: PerE

No. i purchased Peter Homans "ModIo" board instead.
http://homanndesigns.com/store/index.php?main_page=index
Cheers.
Per

Hello.
Has anybody tried to use Fang gamepad with Mach3 and does anybody know whats inside the gamepad, processor etc ? Can i program it for Mach3 ?
Per

Pontus.
If you need any help you can contact me via e-mail "per.ekdahl at comhem.se".
I am using Mach3 to control my router and it is a fantastic program with many features....

Hello Pontus
I am living in Gothenburg and i have built my own CNC router http://web.comhem.se/~u74864760/
There is a forum in Swedish about CNC machines etc....

Hello everybody.
I am building a pendant/control panel and i want to use a PIC processor to talk with Mach3 and keygrabber.
My MPGs is connected to the parallelport and i want all of the other...

Iam sorry NC Cams that i was writing a little bit of "hard".
I am not so very good to explain myself even as i over 45 :-)
You are right about what you are saying and we have to help him to make...

I have worked with Mach3 and win-xp for over 1 years now and i dont have any problems at all so i problably you don´t have tried Mach3 at all.
Best regards.
Per

Hello.
1. I dont think that you can run Mach3 with a cel. 500 it must be over 1Ghz.
2. Mach2/3 can only work with Win XP/2000.
Bets regards.
Per

Hi there.
In Mach3 go in to "config" and then "homing/limits".
In there change the settings for the Z axis.
Best regards:
Per

You have to read the documentation for mach 3 mill chapter 4.5 and forward.
http://www.machsupport.com/documentation/
Best regards:
Per

Try to set the "step pulse" from 1us to 5us.
Hope that helps.
Per.

Hej, Hello.
I am living in Gothenburg Sweden.
Per

Thank you all for the help you give me.
Per Ekdahl

Hello all.
I know there is a way to build a rotary encoder from a steppermotor but how do i build the electronics?
I want to have that encoder as MPG in a pendant for Mach3.
I have a lot of...