Search:

Enikma_II · 01-22-2015, 02:37 PM

Control or motion system X axis have problem

Enikma_II · 01-06-2015, 01:52 PM

What alarm number?

Enikma_II · 11-24-2014, 03:16 PM

Can you check servo drive? How much green LED lite?

Enikma_II · 11-24-2014, 12:48 PM

I think some control FANUC model O can't see leader.
You wiil check air pressor sensor first.

Enikma_II · 11-18-2014, 01:56 PM

Nice sir.

Enikma_II · 11-18-2014, 09:01 AM

Take COM EON and EOF cable out from TP1. Check ohm between COM and EOF have value? push start buttom and check ohm between COM and EON have value?

Enikma_II · 11-18-2014, 07:43 AM

Make sure COM EON and EOF cable is normal?

Enikma_II · 11-17-2014, 11:57 PM

I have lathe machine mazak with system mazatrol cam t3 qt10n. Now I have problem about control panel wiring. anyone can help me please. i need pdf. file for this manual machine. thank you for good...

Enikma_II · 11-17-2014, 11:49 PM

No problem sir.

Enikma_II · 11-17-2014, 11:37 PM

No, I dont have any machine. I m engineer. Now you have 2 choice, repeir board or buy new part.

Enikma_II · 11-17-2014, 11:29 PM

Ummmmm...I m Not sure, my work shop have this code.

Enikma_II · 11-17-2014, 11:20 PM

FANUC O-M or FANUC Oi-M ?

Enikma_II · 11-17-2014, 11:13 PM

Me too ,english so badly hahahaha.

Enikma_II · 11-17-2014, 11:11 PM

Your master board code is A16B-1000-0030 or A20B-0008-0410?

Enikma_II · 11-17-2014, 11:03 PM

Do you have new part for conferm?

Enikma_II · 11-17-2014, 10:58 PM

You can test it by (take out form machine)
1. Short CP2(or CP11)between pin5 and pin6
2. Short COM and EOF
3. Input 220V. to R and S on TP1
4. Trick COM to EON ,now if relay...

Enikma_II · 11-17-2014, 10:42 PM

You can test one card on mainbord.

Enikma_II · 11-17-2014, 10:09 PM

Zero offset meaning home zero or work coordinate? And machine stop is machine's power off or not CRT can display or not?

Enikma_II · 11-17-2014, 09:39 PM

OK, can you take photo unplug point to me via [email protected]? Now you can take A20B-0008-0430 and A20B-0008-0440 out and check CRT and test power ON.

Enikma_II · 11-17-2014, 08:03 PM

How to your precess for enter parameter and you sure enter all PMCPARA?

Enikma_II · 11-17-2014, 07:05 PM

Can you check DNG #A7.0 it on or off?

Enikma_II · 11-17-2014, 06:54 PM

Can you detail me about machine system and take photo 1815 parameter?

Enikma_II · 11-17-2014, 06:52 PM

Can you detail me about machine system and take photo the 1815 parameter?

Enikma_II · 11-17-2014, 06:41 PM

Can you detail about system model and machine model?

Enikma_II · 11-17-2014, 06:20 PM

This error is problem between NC&PC. And you can check on check point to ground is normal or not.

Enikma_II · 10-24-2014, 02:47 PM

-change pulse coder X and Z axis

Best regard.
Enikma_II

Enikma_II · 10-23-2014, 12:42 PM

-check carbon bruch in tachogenerator.
-check vcm and tsa signal.

Best regard.
Enikma_II

Enikma_II · 10-23-2014, 04:17 AM

What's AC motor model & how much do you need

My IndustryArena Login

My IndustryArena Login

Search:

Search: Search took 0.00 seconds.

Thread: Got a problem with cutting corners please help

Thread: atc arm stuck in the down position

Thread: fanuc o md yang

Thread: fanuc o md yang

Thread: A14B-0076-B001 INPUT UNIT

Thread: A14B-0076-B001 INPUT UNIT

Thread: A14B-0076-B001 INPUT UNIT

Thread: mazatrol cam t3

Thread: fanuc 6m system

Thread: fanuc 6m system

Thread: fanuc 6m system

Thread: Fanuc 0-M servo amplifier schematic alarms 401,414,424

Thread: fanuc 6m system

Thread: fanuc 6m system

Thread: fanuc 6m system

Thread: A14B-0076-B001 INPUT UNIT

Thread: fanuc 6m system

Thread: fanuc 15-m

Thread: fanuc 6m system

Thread: EX 1024 error in MV 40/40 MF-M6 mori seiki

Thread: EX1047 alarm

Thread: Error EX 0296 (411) Magazine Servo Alarm

Thread: Error EX 0296 (411) Magazine Servo Alarm

Thread: 510 error(cut.feed-t.c.err.)

Thread: fanuc 6m system

Thread: fanuc 6t not positioning correctly

Thread: fanuc 6t not positioning correctly

Thread: CNC Parts

This website uses cookies