Search:

I have v20 and I am not interested in upgrading at this point.

I am trying to wrap text on a radius. Can someone help? It is a 2" diameter that runs lengthwise in the x axis. The text is about...

OK that will work great for the output from Mach but what about the input to Mach?

I had an old rutex 4 axis system that I gutted out a few years ago. R990 drives, motherboard and relay board.

I have a full size mill with an Anilam control, and running a job that I need an...

Hello,

I have a full service job shop in the Fort Wayne, IN area that is currently operating under capacity.

CNC Turning with barfeeder, 4 axis CNC Milling, Manual Turning, Manual Milling,...

Tobyaxis quote:

"To be honest, they have to my knowledge never Laughed at a potential customer. Money is Money and they really Value their customers.

You can ask anyone that has purchased any...

I have 3 A2100 powered lathes and they are great. I wish they still made them.
I also have 1 machine that is running Mach 3 and servos.
I would expect that if you complete the project, you would...

In my earlier post when I said "crankcase vacuum", I meant "crankcase pressure". I think Richard knew what I meant. Sorry for the typo. As far as the 12L and Al pistons I will look into different...

2 stroke engine pressure does not require alternating pressures. They simply require some sort of crankcase vacuum (i.e. alternating pressure created from pistons) or a fuel/air mixture forced into...

Cincinnati Machine still handles parts for nearly every machine they have ever built. I deal with them very frequently. I don't have the 800 number at this time, but you can goto...

Hello everyone. I have always wanted to build a radial engine, so about 3 weeks ago I finally started one.
I thought I would post some pics, and get some input. The project started out as a 4...

I have my own shop with 6 cnc's. I used Valcool 700 for several years and liked it real well. hired a guy that broke out terrible, so we switched to Cimtech 495 (full syn). I loved it immediately....

Me too.

[email protected]

I have a Mazak lathe (SQT-15M) and I know that Mazaks are high maintenance!
This is my first and probably last Mazak. Did you know that MAZAK got its name from KAZAM spelled backwards? If that isn't...

Age 22 and you are a "CNC Expert"? Hmmm? It took me more than a couple of years.

mscdirect.com or 1-800-645-7270

AC or DC depends on the servo motor. AC motors and the electronics to drive them are much more expensive. My motors just happen to run at 120VDC. You can get servo motors in a wide variety of...

I am in the proess of doing the same, only my motors were SEM. Goto Rutex/Servo Drive to see my thread. If the motors are similar to mine they an easily have an enoder added to them. The original...

That monster runs all 4 motors @ 120VDC. The three smaller ones are inductors for each motor. Rutex has just advised me not to use them, so they will be removed. Yes the larger relay is 3 PHase for...

The motors and 4th axis drive drive should be here on 14 march. I still need to put in a 24vdc power supply, and that should be about it. Any question, critique's, or suggestions?

Control Box with Rutex R90H's installed. It is almost finished. Motors and the forth axis drive should be here on Mar 14. Hope to have machine running by 17 Mar.

Yes, the motors are 120 volt dc. I am going to continue to use the 120v power supply and 8700mf capacitor, but I am going to chang out the motor to these...

I am in the processs of converting and Anilam Crusader to Mach 2 control.
I have 4 Rutex R90H, Relay board, and Mother board. I am using the original 140VDC to power the motor. My question is, would...

The machine already had ballscrews. Kent

Well I spent some money. I ordered 4 of those motors, and 4 Rutex R90H drives, Motherboard, relay board. I hope it all goes together well. This is my first one.
I am going to run 115VDC to those...

The servo motors say 140v dc max on them. they have an encoder, but only 2 wires? i can replace the encoders, and i have the dc power supply, but my problem is drives. how much speed would i lose...

I have purchased a Lugun Mill with a dead Anilam Crusader controller. The servo motors are still good and I would like to use them if possible. I'm not sure if they are AC or DC servos. (Will Gecko...

F riggin
A merican
N o
U nderstand
C hinese

I am going to use 2 nut method with a spring in between to create a 1" od (not sure yet on the tpi) ab nut on my "y" axis. (If there is a better method of creating an ab nut, please enlighten me.)
...

I went through Applied Industrial Technologies I had about $1400.00 in 2 10 ft predrilled shafts, 20 ft of supports and 2 twin fluoroliner pillow blocks.

Hi everyone. I 've been reading the forums for quite a while, but this is my first post. I am just getting started on my plasma table, and I will have many questions to post in the near future.

I...