hi,
i have a Hurco km3p Milling Machine , I have an error that says
cannot keep up on B axis
any help will be highly appreciated
regards
Type: Posts; User: nuzmeed
hi,
i have a Hurco km3p Milling Machine , I have an error that says
cannot keep up on B axis
any help will be highly appreciated
regards
I know BLOKE is the HERO of Hurco CNC KM-3P machines.
Pls BLoke help me out, I will be very obliged for this.
any buddy ????
Any Buddy Pls just Give me an Idea for What to Check
Hi, I have a problem in Hurco KM3P, After Power Power on, when I press Start Button, The Spindle Motor Starts Running Automatically continious and
X, Y , z axis are not working properly .
can...
hi, the problem is resolved. actually the connection of EDIT KEY Lock was loose from Inside. I have fixed it.
thanks for the Support Guys
the Edit LOCK key is in ON position
can you please describe in detail to follow the instruction .
I will be glad for it .
hi,
I have a CNC Machine of FANUC MV-series 106A.
when I try to give any input to position it says " Write Protected "
can any one pls guide me to remove this error
thanks
nuzmeed
dear efinkg,
thanks for your offer, I have repaired it by myself, Actually there are 4 Transistors on each card of Servo drive , one Transistor of X-Servo Card was Burned I have replaced it with...
any One please help me out ......
I will be very much obliged ....
hi,
I have a problem with my Hurco Milling Machine, Its Carbon of Y motor were Finished, after a long Period I got the Acurate carbon Brushes. when I have Placed the carbon I have tested it by...
now I have Changed the carbon Brush of the Y motor, when I Power on the Machine it shows the Servo Fault
Any Clue ???
Assistance will be Highly Appriciated
Now My Problem is That
May Y-Axix is Probleming, It shows Error on " Error Detected on Y "
I have changed the Y connector to X , Than the Error Shifted on X
I concluded that MAy be the Fault is...
I took a Risk by removing the 24vdc wire and placing a temporary 24vdc 40Amp switching Power supply and than tryed it powering up it worked.
Now I will try to repair the 24vdc power Supply
...
i have checked the power ratings of the main power supply
the light Blue Wire from Right Hand side is not Giving the 24VDC out put.
can This be the main Problem for not starting the Machine
Rest...
My machine is again having the same problem, the power button is not working again.
may be there is a possibility that air is comming but, the air pressure switch is not working. how can i check...
hi, I don't Know what Happened but It is working now. today when I switched On the power its working.
any ways Thanks for the Help. But I am Still Curious that what is problematic on it
I have Checked the Air Pressure Switch, Its working Fine.
Where is Overload ??
its not working man, have check the cable its okay. is there any thing else
hi, I have New problem now.
when I switch on the Machine, when I press the power button from the console it does not start the Machine.
only DS1 and DS4 relay LED light blinks slightly on the...
Any Way Thank you very Much For your Helpful Assistance
hope to see you cooperation in future too.
Nice to meet you here.
best regards
Max
yes MAgic Codes = Enter ***** enter ( for me these are Magic Codes )
yes is there any possibility to run the machine software in a PC
Thanks BLoke!
It really helped me out.
now the Direction is Ok.
one request more If you could provide me the DIP switches settings and Magic Codes applied on it. is there any possibility to...
Now
I have Replaced all the things back in original position as per your Direction.
and than Tried enter 639 enter 0 enter, enter 999 enter .
it rebooted and now at least, the + and - keys...
I have Noticed One Thing!
that Machine is again in " Machine Configuration "
Have Managed to change the parameters in Metric system now its ok.
X=610.000 MM
Y=355.000 MM
Z=127.000 MM
...
still the same problem in X-Axis, Spindle is working Fine, Y-Axis is moving fine.
But in X-axis, it is going opposite side. also the +, - keys are working opposite.
i have Changed Mc1488, and...
I did exactly as you guided me, can you please guide me further ???
yes i have done It. noted all the Jumper Settings and Swapped both the EEPROMs and
after changing the settings
placed the Zspindle card to X.Y Slot. and X.Y to Zpindle SLot.
now when I...
Now there is another Problem!
the main problem or fault on this machine is , its Y axis was problematic.
when any job is placed. it works fine after 2 or 3 hours it damages from y axis.
i...