See in ladder the Bits of rotation commands , Binary and strobes from Encoder is there or not . The Feed back
Regards
Type: Posts; User: yours_prabhat
See in ladder the Bits of rotation commands , Binary and strobes from Encoder is there or not . The Feed back
Regards
Try PC 2100
Try to increase the z + value to 99999999 in soft OT parameter , . in Puma 8 S some Bits are there where the CAn+P during power hold will not work , So try to increase the value of the Soft OT in ...
Sir mekanika cnc, m36 is excellent , you are doing the right job and your decision is perfect.
What is the alarm Number ? Is it Soft OT or hard OT alarm ? If it is a soft OT than CAN +P will work If not than you have to do other stuffs , Please confirm with alarm Number .
regards...
check the macro program , or the tool change is in Ladder only ??
PM me your email i will send you a circuit you can make in your shop , just 3-4 components are used for that
Go to second reference and do the tool change
there is an abnormal load in motor . see the auxillary contractor/overload of the Motor Supply and / or see the ladder for the Details {it is an external alarm } also check most of the time this...
It can be useful for you
6064 4AMP Stepper Motor Driver Kit. massmind
you can ask a professional to do a Laser Calibration axis for high precise positing accuracy and Repeatability
rishikesh Sir,
put a clamp- tester between the earth wire and in a phase together , you will find the reading , Better put a 0.001MFD/1KVA capacitor between all 3 step down phase after isolation...
Check the regenerative Circuits , The Opto couplers . and the Fusuable resistors
regards
prabhat Mishra
Summarized Advantages - HMC vs. VMC
Spindle Utilization
Fewer machines required
Remember 25% vs 85%?
Shorter Throughput Times
warm welcome sir .. The mach 3 you are using , how do you feel about the ease of access for ?
dear jlavery
Is it fanuc 18i control ?
Please confirm
regards
Parameter 0535 = X axis
Parameter 0536 = Y axis
regards
Prabhat
[email protected]
In this case you can use it .
regards
Sir the 1XXX alarms are user alarms , This is designed or written by MTB ( Machine Tool builder ) and it varies machine to machine . For manual send me your e mail id i will send you the manual . you...
Yes you can use it , May be you required a little pin configuration change in multi strand cable ( I mean on connector)
regards
Check the Transistor Module , The input voltage circuit up to module , The capacitor discharge Circuits , The Opto-couplers, The small Diodes , and Driver Switching IC .
Just cross examine the...
Dear Sir
The G50 = Define the maximum spindle speed.
Its a excess alarm , Either overload mechanically . or excessive deviation
Reset the control . check the motor position physically and axis
you will get a rigid and perfect machine ( Old is Gold ) still in germany , Europe , USA , India , Thefailure rating of 6 T control are less than others ...
Just see here
http://www.cnczone.com/forums/fanuc/171791-looking_fanuc_6t-b_manual.html
regards
Prabhat
Ganeshan Sir
You are expert why you are talking in this way .. Sir you are the master of CNC in south India and in all India if i am not wrong ..
regards
[email protected]
To check dovetail tram for straightness:
1. Jog X axis in the plus direction as far as it will
go.
2. Mount indicator base to the bottom of the turret
as shown.
3. Place indicator needle on...
what is the make ? what is the Encoder number and what is the problem?
Check the Pulse coder and limit Position , The feed back to the controller is wrong. The actual position is different .Check the axis position .
basically these all are user alarm ( OUTSIDE...
1057 ‘Undefined subroutine’
Detection During execution.
Cause A (CALL, PCALL…) has been made to a subroutine that was not defined in the CNC
memory.
Solution Check that the name of the subroutine...