Search:

The okay. Making permanent move to Linux. Windows sucks. Always has.

I have emailed you the PCNC profile.

The machine is having some very odd issues. I am assuming this is related to Windows 11 security issues or W11 as a whole.

1. Randomly at startup the Tool...

Hello,

I have installed the license key and still at startup of the TNG I get random errors telling me the PC is not authorized. I am wondering if it is related to a security or certificate error...

[email protected]

Most likely it has lost its tool data or cannot make to second reference. Send me your company information.

Have the input shaft bearings been replaced and it could be the encoder. What control? I am an ex Toyoda service tech. Typically no more than a few thousandths on gear slop. Also could be the splines...

Believe so..

I suggest contacting my good friend and colleague at Tryco Mahine Works in Porter Texas. His name is David Cook. You wont find a better family or business partner. They have a Citizen with bar feed....

Yeah the screensaver has no effect on Mach.

I have been a cnc builder and service engineer for too long to remember. I strongly urge that any machine you plan to make money from have servos vice steppers. It really stinls to be caught pants...

Do you have a closed loop system? If yes, the it is your contoller.

If not, then it is the power supply common.

Steppers lose steps regardless but if closed loop not more than a few without a...

What is the max ADC inputs for all boards if connected as you stated. 1 KFLOP, 1 Kanalog, 4 Konnect, 2 Snaps?

I suppose the better question is are the In0~In3 ADC inputs on JP12 mapped the AIN0~3 on JP6? If not, then are these 4 additional ADC inputs? If so, then what are they for?

Fantastic. Just hat I was looking for. Thanks Tom and Jeffserv.

Once I have the final I will send it to you. It should work with most Taiwanese ATC's. Almost all including Toyoda (FH Series to...

I am wondering if the simplest way is to utilize a single ended encoder input for the last acis channel with no output. Then scale the count accordingly. Read the position and act on that. Since the...

It is roughly 2 -3 PPS which is not a lot considering. I would think one could catch that in a 100ms loop. Just needed to see how to decode it. One AB cycle = 1 count plus. One BA cycle = 1 count...

All,

I have a magazine setup that has 2 switches that act as a quasi encoder. What I am looking for is a starting place to build a C program that will increment and decrement a counter variable. I...

Tom,

Thanks for putting up with my nagging questions. Lol. I have some interesting ones:

1. How do you assign a value to a variable in a c. program then once the KFLOP has powered down, hold...

Okay. I am working to install the Kanalog. MY drive has an offset input. Is there a parameter in KFLOP that will set this analog offset before the signal is sent? or should I use the drive to create...

Part of the schematic is cut off. Send the entire page to the right of the motor in the drawing.

If you can find the pin out drawing for the signal connector I can help.

99% sure the Kanalog...

Okay. I figured out the encoder channel was set to 4 and not 8. I have the motor servoing now. But I cannot get more than say 250 rpms. Smooth movement but slow. I check the pwm output % and it maxs...

Okay. I got the SnapAmp installed. Here is what I have set up.

I have the encoder wired to the first diff encoder AB and then the Z to pin 68. I can see the encoder counts in diagnostics. But, I...

I have a 2K PPR differential encoder. I have a Kanalog board. I have a KFLOP. Currently I have the 2 boards mounted and powered. I am receiving the AB channels from the encoder fine. 1 Rev = 8000...