Don't have to store on the website for the DVDROM downloads anymore but they are available by request, [email protected]
Type: Posts; User: hoss2006
Don't have to store on the website for the DVDROM downloads anymore but they are available by request, [email protected]
You can email me at [email protected] for new links and passwords.
Hoss
I think I sent you this pdf by email of the original website cnc conversion page, the full size blueprints are in the allx2prints download.
Hoss
P.S. The links probably don't work much since this...
The X2 getting the job done at work.
Converted the Grizzly 7x10 to 5C with a 3C collet closer adapted to it.
Hoss
https://www.cnczone.com/forums/attachment.php?attachmentid=450066&stc=1...
The X2 making money at work.
Converted the Grizzly 7x10 to 5C.
Hoss
449965
449967
449969
I run UCCNC on the G0704 now with a UC400 board, love it. Great probing pages and easy to set it up. Only thing I didn't figure out yet was
the ATC macro but I adapted the ATC4 onto the X2 at work...
Thanks fellas, figures I get healthy and all this rona BS hits lol.
Here's a couple picks of the X2 all rebuilt now at work making a part for the company and one from what it looked like in February...
I had the gastric sleeve surgery almost 4 years ago. People probably didn't know I was wheelchair bound since 2011 with the weight and arthritic knees.
300 off and new titanium knees I made on the...
https://www.cnczone.com/forums/attachment.php?attachmentid=448202&stc=1
Lost 300 lbs over the past few years, feeling great.
Still available on my site. Nobody archives them but me.
It's not going anywhere, I'm back into CNC and just rebuilt the old X2 Freak from the ground up too. Use it at work now.
G0704store
X2...
Guess a PM won't work so email me at [email protected]
Hoss
PM sent, Merry Christmas!
Hoss
Get em while you can, probably won't renew the website after this year if it can't pay for itself.
G0704 DVDROM Download
DVDROM Super Combo Download
Hoss
Yes the plans are still available I just don't get on here like I used to.
G0704store
Hoss
lol not dead busy with work and school, x2 stuff is moved to the g0704 site.
Hossmachine Store
Hoss
Yes it is, G0704store
Hoss
that thing didn't work, used belleville springs with the drawbar later on which is in this thread somewhere, iirc it used the stock drawbar.
Hoss
btw the g0704 site is still up.
[email protected] is back up and running now.
Hoss
He's fine, busy gettin healthy. :) Working on combining the websites for convenience is all.
Hossmachine Store
Hoss
Could be your pc, I tried upgrading mine once and the rapids went to crap, put the old pc back on and the rapids went back to fast. You might think about using a smoothstepper if you aren't now.
Hoss
Getting some use out of the old g0704 motor, using it to make a small wind turbine to charge a 12v battery when I move out to the Alaskan bush lol. Blades are cut from a 4" pvc pipe.
Hoss
With stock screws you aren't going to get very fast rapids 50ipm was all I got with a 2:1 belt drive. Gotta love those low friction ballscrews. ;-)
Set accel quite low to give it more ramp up time...
Most likely, mine came out pretty easily but have seen where others have had to press them out, particularly the upper bearing.
Hoss
Yes that one at the top and the big one at the bottom.
Hoss
Have you removed the retainers from both top and bottom? If you are replacing the bearings there isn't any need to be protective of the bearings.
Hoss
You could always mill your own custom fit t-nuts, been so long since I messed with that that I don't recall what I used.
Hoss
What he said, those bearings are there for a reason and it is more necessary with a belt drive as lateral tension is constantly being applied from the belt tension. Upgrade those bearings if they are...
Sure thing.
Hossmachine Store
Hoss
Yeah the top of the flange will likely need a little more removed.
You can wrap the nut and screw with tape just leaving the little bit to grind exposed, grind a little at a time to keep it from...
The non stepper end of the x screw just calls for a single roller bearing just lightly snugged to prevent whipping of that end of the ballscrew, the stepper side with double bearings is where to...