... IF, the bios has been reset I bet you have to change one or more of interrupts to factory settings to fix the conflict...Want ever they were or should be.
DJ
Type: Posts; User: machinehop5
... IF, the bios has been reset I bet you have to change one or more of interrupts to factory settings to fix the conflict...Want ever they were or should be.
DJ
...check all cool Fans.....could try removing and reinstalling all the IC Chips on all the boards. Look around or feel for anything getting extra hot.
...try replacing the FDD in the PC and see if, you can get it running.
Hi leeko,
...Yes. I would agree the PS would be the 1st to check or time to replace.
Good luck,
DJ
...good to hear. Sometimes have to get a little creative.
DJ
...If, you have DC Axis drives ....than yes. It sounds like a Tach issue. Dirty brushes, carbon dust, etc. or even possible just bad Tach.
DJ
...Welcome Duane,
nice this machine has the knee(W axis) power feed motor......there is a few things to check. Collect open/closing operation should be checked with a Tool. Also, most likely...
...try moving to and set Z Home (SETH) at Z+2.5 above normal machine zero..or possible (SETZ) command.....I think the machine should remember the TC position. See how the CS functions after you...
...might help if, knew what machine you have.
...be very careful where and what you're unplugging before knowing. There are some bios battery things going on you don't want to lose. Good Idea to do a backup 1st to things.
good luck,
DJ
...the Data Bit should be 7 and sounds like a Cable problem. There are few different ways to interface using RS232C. How do you have your cable wired or type Cable? Null Modem is what you need I...
...looks like its a water trap Part#58-2012 maybe.
https://parts.haascnc.com/haasparts/en/USD/search/?q=air+filter&machineType=&model=&year=
Enjoy,
DJ
...read Post #4 may help.
https://www.cnczone.com/forums/milltronics/17762-software.html
By the way do you have any Cad Cam in house system you use?
here is a free one. It has Post Process for...
Good you have save Params...that looks like the Baud rate maybe set wrong between cnc to PC try 4800 or 9600........also there were alot of cheap USB to RS232 converters sold that had bad chipsets in...
...I'm not a Hurco guy but......If, your machine will run with the borrowed board..there should be a way to get the files you need maybe.....I think you can Save the Parameters, Backup files to FDD...
...sounds like the bios has reset ...do you have Keyboard to boot to BIOS? older DIN 5 pin plug somewhere 90's machines most of the time. Then, set the date/time then.... look for Auto detecting the...
...Keyboard failing or sticky keys? Does your keyboard have a PC power button? Disable it ...if, possible.
DJ
...try changing "Bit Parada" to 1 or 0
DJ
...It's a little tricky to do and it has been awhile sense I did this A axis Engraving on a Fadal 4020HT machine.....Cam Wrapping is one part of programming needed with a Fixed Subroutines L9201 for...
...I think the RealCom Mode is what you need to use. Then, each PC install a RealCom Port with NPort Admin program IF, I remember correctly....
...Aluminum Can for shim stock. Remove the Ink and plastic coatings.:cheers:
DJ
...If, the Time/Date is Jan 1st in bios then, all settings were lost so, you have to reset Time/Date and do a AutoDetect to find HDD to boot from in BIOS.
DJ
double post deleted
You said you never had this Spindle running so, possible that someone has a Parameter set wrong hopefully. Try...disconnecting the Encoder and see if, the Spindle errors out the same code. Check...
...for anyone reading this thread without a manual..... here is list of G Codes for Okuma Lathe.
https://www.helmancnc.com/okuma-lathe-g-and-m-codes/
DJ
...G05 or G07 may or may not change anything but, does effect the look ahead the control uses for accel/decel block to block.... try changing from what ever default is on your control. See what...
...try exporting with .IGS or IGES ext to Bob Cad.
...Power Supply most likely. +5VDC Logic or 12v going to the Main CPU system. Could try using some Cooling Spray to find the problem Component....
....welcome to the zone.
After briefly reading thru your Eding Software manual...most of the Beginner questions are answered but, to someone new to CNC it's hard to know where to start process...
...inspect (if possible) or replace the main High Voltage relay/ contact's for Spindle Drive. Old age and mileage from Arcing they surprisingly do wear out
good hunting,
DJ