Kollmorgen S Series A/C Servo drives: How do I connect them for Mach 3 Step/Direction

Quote:

---

should be easy to diagnose this.... see screen shot of how it should be set up. did you pick "remote enc input? What screenshot? I see no attachments.
Is motor holding position or just free wheeling? Not since I re-did the wires. But first try with only two wires connected the axis was 'creeping' in one direction with no control.

---

sorry, got a customer call and forgot to attach. will try to remember and do after Jag show......

if drifting, that guarantees you were NOT in mode 4 only velocity mode.

Dear, can you put wiring diagram here. Best regards.
[QQUOTE=jxdxwx;1690056]

I will look over the drive settings when I get home and let you know. Yes my MotionLink computer is connected to the internet. It is currently the same computer that I am running Mach3 on also. Should be able to minimize screens if you need both to be running.

How and when do you want to connect thru internet ?

John[/QUOTE]

Diagrams attached.

Let me know if it helps.

You sent me another PM but my mailbox is full.
I didn't get it. so resend or post here.

Quote:

---

Originally Posted by shejta

Dear, can you put wiring diagram here. Best regards.
[QQUOTE=jxdxwx;1690056]

I will look over the drive settings when I get home and let you know. Yes my MotionLink computer is connected to the internet. It is currently the same computer that I am running Mach3 on also. Should be able to minimize screens if you need both to be running.

How and when do you want to connect thru internet ?

John

---

[/QUOTE]

TEAMVIEWER PROGRAM TO CONNECT. You need to have it all turned on and running for me. I would hook in and help you for 15-20 minutes. I have hamfest tomorrow morning so maybe tomorrow (Sat) 2:15-2:30pm EST? or maybe sometime on Sun? Since it is free help, I cannot do early next week as I have commitments.

Mike, thank you but I am actually currently running fine.
The msg was an old one that another user cut and pasted and referred to.
I am helping him with my wiring schematics.

May take you up on some fine tuning at somepoint in the future, but for now all is well.

THANKS!!!
John

thanks!

Dear, Thank you so much for help, In next couple minutes I will post images of drive and screenshots from program setup. Just to note, on display is currently E03. ( with dot). What that mean? Best regards

Quote:

---

Originally Posted by shejta

Dear, Thank you so much for help, In next couple minutes I will post images of drive and screenshots from program setup. Just to note, on display is currently E03. ( with dot). What that mean? Best regards

---

Attachment 330598Attachment 330600Attachment 330602Attachment 330604Attachment 330606Attachment 330608Attachment 330610Attachment 330612Attachment 330614Attachment 330616Attachment 330618

Also, I want ot connect this board: Sorotec - Interface Advanced PRO and manual is located on this link http://www.sorotec.de/webshop/Bedien...ut8-Manual.pdf

Quote:

---

Originally Posted by shejta

Dear, Thank you so much for help, In next couple minutes I will post images of drive and screenshots from program setup. Just to note, on display is currently E03. ( with dot). What that mean? Best regards

---

apples and oranges? there is no such display E03 on a Servostar SE or SR series drive. There IS that display on an S600 drive and it would mean it is a 3amp drive and E for ENABLED. Totalaly DIFFERENT animal.

I cannot handle discussing this on here; I MUST use email as I cannot sit in front of this computer all the time. my email is [email protected]

HA! so I just saw ur pictures. you are talking about a TOTALLY DIFFERENT DRIVE than everyone else previously.

I have no idea what YOUR problem is.

I wanted to leave office 2 hours ago and have been stuck with a couple customers needing help; email me if you would like me to respond maybe tonight. It is WAY past Miller time here!

I'm trying to do the same thing as the OP in this thread.
I have a S310 hw rev 3.01, firmware 3.88 and was able to connect to the DBL4N00750 - 03M - 000 - S40 servo using DriveGUI and jog the motor with motion service.

I need to control the S310 drive with step/direction input as described on pg 88 of the manual. The problem I'm facing is that every time I try to enter the setup wizard, the DriveGUI program crashes. I'm running Windows10.

Is there a known issue and/or workaround with using the DRIVEGUI setup wizard on older drive firmware?

Alternatively, if anyone has a suggestion for a better drive to use than an s310 that can be had on eBAY for under $500, I would appreciate suggestions. I prefer to run on single phase 220V.

Hello
Driver.exe (program for kolmorgen setup) doesn’t work very well on windows 10. Try to use windows compatibility options and set to XP compatibility or Windows 7. I am implemented several machines using those drives and step - dir input. Mostly used CSMIO ip-m or S because they use differential output. A lot of help I got from Mike Kilroy. He is genius.

QUOTE=MD21921;2440718]I'm trying to do the same thing as the OP in this thread.
I have a S310 hw rev 3.01, firmware 3.88 and was able to connect to the DBL4N00750 - 03M - 000 - S40 servo using DriveGUI and jog the motor with motion service.

I need to control the S310 drive with step/direction input as described on pg 88 of the manual. The problem I'm facing is that every time I try to enter the setup wizard, the DriveGUI program crashes. I'm running Windows10.

Is there a known issue and/or workaround with using the DRIVEGUI setup wizard on older drive firmware?

Alternatively, if anyone has a suggestion for a better drive to use than an s310 that can be had on eBAY for under $500, I would appreciate suggestions. I prefer to run on single phase 220V.[/QUOTE]

Thanks for the windows version suggestion! I was able to get it configured using a windows7 PC.

Quote:

---

Originally Posted by MD21921

Thanks for the windows version suggestion! I was able to get it configured using a windows7 PC.

---

Thanks shejta for helping him!