Re: Linuxcnc 2.5.2 won't run
hal_parport: dlopen: /home/maura/linuxcnc-rtos/rtlib/hal_parport.so: cannot open shared object file: No such file or directory
thats your problem, if you have hal_parport.so maybe you can direct it to the correct location, or add a link to in where it thinks it should be.
you have a parallel port on your computer right?
the easiest way is to just install the livecd from the website.
Re: Linuxcnc 2.5.2 won't run
Hi Alan,
went to website and could not find liveCD that has linuxcnc 12.04 with linuxcnc 2.5.2. I need to have linuxcnc 12.04 installed to run FlatCAM. So if you can help guide me to make the modification that you suggested, I would greatly appreciate it.
Thanks
Re: Linuxcnc 2.5.2 won't run
About half way down the page - it explains on how to install linuxcnc 2.6 on 12.04 32bit
LinuxCNC Documentation Wiki: UpdatingTo2.6
sam
Re: Linuxcnc 2.5.2 won't run
Followed your instructions. The first of code came back with errors. Please see below and advise if possible.
maura@ubuntu:~$ sudo apt-get install linuxcnc
[sudo] password for maura:
Reading package lists... Done
Building dependency tree
Reading state information... Done
Package linuxcnc is not available, but is referred to by another package.
This may mean that the package is missing, has been obsoleted, or
is only available from another source
E: Package 'linuxcnc' has no installation candidate
maura@ubuntu:~$ sudo apt-get update
Hit 301 Moved Permanently precise-security Release.gpg
Ign LinuxCNC.org base Release.gpg
Hit 301 Moved Permanently precise-security Release
Hit Index of / precise Release.gpg
Hit http://ppa.launchpad.net precise Release.gpg
Get:1 Index of / precise-updates Release.gpg [198 B]
Ign LinuxCNC.org base Release
Hit Index of / precise Release
Hit http://ppa.launchpad.net precise Release
Get:2 Index of / precise-updates Release [49.6 kB]
Hit 301 Moved Permanently precise-security/main Sources
Hit http://ppa.launchpad.net precise/main Sources
Ign LinuxCNC.org base/2.6 TranslationIndex
Hit 301 Moved Permanently precise-security/restricted Sources
Hit 301 Moved Permanently precise-security/universe Sources
Hit http://ppa.launchpad.net precise/main i386 Packages
Ign http://ppa.launchpad.net precise/main TranslationIndex
Hit 301 Moved Permanently precise-security/multiverse Sources
Hit 301 Moved Permanently precise-security/main i386 Packages
Hit 301 Moved Permanently precise-security/restricted i386 Packages
Hit 301 Moved Permanently precise-security/universe i386 Packages
Hit 301 Moved Permanently precise-security/multiverse i386 Packages
Hit 301 Moved Permanently precise-security/main TranslationIndex
Hit 301 Moved Permanently precise-security/multiverse TranslationIndex
Hit 301 Moved Permanently precise-security/restricted TranslationIndex
Hit 301 Moved Permanently precise-security/universe TranslationIndex
Hit Index of / precise/main Sources
Hit Index of / precise/restricted Sources
Hit Index of / precise/universe Sources
Hit Index of / precise/multiverse Sources
Hit Index of / precise/main i386 Packages
Hit Index of / precise/restricted i386 Packages
Hit Index of / precise/universe i386 Packages
Hit Index of / precise/multiverse i386 Packages
Hit Index of / precise/main TranslationIndex
Hit Index of / precise/multiverse TranslationIndex
Hit 301 Moved Permanently precise-security/main Translation-en
Hit Index of / precise/restricted TranslationIndex
Hit Index of / precise/universe TranslationIndex
Get:3 Index of / precise-updates/main Sources [455 kB]
Hit 301 Moved Permanently precise-security/multiverse Translation-en
Hit 301 Moved Permanently precise-security/restricted Translation-en
Hit 301 Moved Permanently precise-security/universe Translation-en
Ign http://ppa.launchpad.net precise/main Translation-en_US
Err LinuxCNC.org base/2.6 Sources
404 Not Found
Ign http://ppa.launchpad.net precise/main Translation-en
Err LinuxCNC.org base/2.6 i386 Packages
404 Not Found
Ign LinuxCNC.org base/2.6 Translation-en_US
Ign LinuxCNC.org base/2.6 Translation-en
Get:4 Index of / precise-updates/restricted Sources [8,028 B]
Get:5 Index of / precise-updates/universe Sources [106 kB]
Get:6 Index of / precise-updates/multiverse Sources [8,909 B]
Get:7 Index of / precise-updates/main i386 Packages [790 kB]
Get:8 Index of / precise-updates/restricted i386 Packages [12.2 kB]
Get:9 Index of / precise-updates/universe i386 Packages [244 kB]
Get:10 Index of / precise-updates/multiverse i386 Packages [15.4 kB]
Hit Index of / precise-updates/main TranslationIndex
Hit Index of / precise-updates/multiverse TranslationIndex
Hit Index of / precise-updates/restricted TranslationIndex
Hit Index of / precise-updates/universe TranslationIndex
Hit Index of / precise/main Translation-en
Hit Index of / precise/multiverse Translation-en
Hit Index of / precise/restricted Translation-en
Hit Index of / precise/universe Translation-en
Hit Index of / precise-updates/main Translation-en
Hit Index of / precise-updates/multiverse Translation-en
Hit Index of / precise-updates/restricted Translation-en
Hit Index of / precise-updates/universe Translation-en
Fetched 1,690 kB in 51s (32.8 kB/s)
W: Failed to fetch http://linuxcnc.org/precise/dists/ba...source/Sources 404 Not Found
W: Failed to fetch http://linuxcnc.org/precise/dists/ba...-i386/Packages 404 Not Found
E: Some index files failed to download. They have been ignored, or old ones used instead.
maura@ubuntu:~$
Second entry came back with the following;
sudo apt-get install linux-image-3.4.55-rtai-2 rtai-modules-3.4.55-rtai-2
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Unable to locate package linux-image-3.4.55-rtai-2
E: Couldn't find any package by regex 'linux-image-3.4.55-rtai-2'
E: Unable to locate package rtai-modules-3.4.55-rtai-2
E: Couldn't find any package by regex 'rtai-modules-3.4.55-rtai-2'
maura@ubuntu:~$
Please advice
Thanks
Cpeter
Re: Linuxcnc 2.5.2 won't run
Did you update your repositories correctly so that it knows the location of the linuxCNC packages? This error shows there might be a typo or something in your repo:
Err LinuxCNC.org base/2.6 Sources
404 Not Found
Make sure your repository has:
deb LinuxCNC.org precise base 2.6
for 12.04.
Mark
Re: Linuxcnc 2.5.2 won't run
hi wendtmk,
thanks alot for the help. It was what you said. I just needed to learn how to use the software manger. After running the app. I ran into an install issue. Please review and advise please.
Get:2 LinuxCNC.org precise/base rtai-modules-3.4.55-rtai-2 i386 3.9-shabby-memleak-2013.12.13-1 [326 kB]
Fetched 37.0 MB in 15min 30s (39.8 kB/s)
Preconfiguring packages ...
Selecting previously unselected package linux-image-3.4.55-rtai-2.
(Reading database ... 223152 files and directories currently installed.)
Unpacking linux-image-3.4.55-rtai-2 (from .../linux-image-3.4.55-rtai-2_3_i386.deb) ...
Done.
Selecting previously unselected package rtai-modules-3.4.55-rtai-2.
Unpacking rtai-modules-3.4.55-rtai-2 (from .../rtai-modules-3.4.55-rtai-2_3.9-shabby-memleak-2013.12.13-1_i386.deb) ...
dpkg: error processing /var/cache/apt/archives/rtai-modules-3.4.55-rtai-2_3.9-shabby-memleak-2013.12.13-1_i386.deb (--unpack):
trying to overwrite '/etc/udev/rules.d/99-rtai.rules', which is also in package rtai-modules-2.6.32-122-rtai 3.8.1-linuxcnc1
Errors were encountered while processing:
/var/cache/apt/archives/rtai-modules-3.4.55-rtai-2_3.9-shabby-memleak-2013.12.13-1_i386.deb
E: Sub-process /usr/bin/dpkg returned an error code (1)
Re: Linuxcnc 2.5.2 won't run
You might want to run "sudo apt-get clean" from the command line. That error you are running into sounds a bit like some issues with the residual packages from the previous tries at the installation.
After that operation is complete, try again to download the linuxCNC packages.
Mark
Re: Linuxcnc 2.5.2 won't run
Hi wendtmk,
Tried "sudo apt-get clean" from command line and it ran for only 1 or 2 seconds. Don't think it did anything, but ran install again and got this error;
Errors were encountered while processing:
/var/cache/apt/archives/rtai-modules-3.4.55-rtai-2_3.9-shabby-memleak-2013.12.13-1_i386.deb
E: Sub-process /usr/bin/dpkg returned an error code (1)
I have no idea what this means or what to do. If you can please advise.
Thanks
Re: Linuxcnc 2.5.2 won't run
After another install attempt, I dicided to try and run program; got this message:
maura@ubuntu:~/linuxcnc-rtos$ linuxcnc
LINUXCNC - 2.6.0-pre1
Machine configuration directory is '/home/maura/linuxcnc/configs/sim.axis'
Machine configuration file is 'axis.ini'
Starting LinuxCNC...
RTAPI requires the real-time kernel 2.6.32-122-rtai to run. Before running
this realtime application, reboot and choose this kernel at the boot menu.
Realtime system did not load
Shutting down and cleaning up LinuxCNC...
RTAPI: ERROR: could not open shared memory (errno=2)
/usr/bin/linuxcnc: line 498: 4594 Segmentation fault (core dumped) $HALCMD stop
RTAPI: ERROR: could not open shared memory (errno=2)
/usr/bin/linuxcnc: line 498: 4600 Segmentation fault (core dumped) $HALCMD unload all
RTAPI: ERROR: could not open shared memory (errno=2)
RTAPI: ERROR: could not open shared memory (errno=2)
RTAPI: ERROR: could not open shared memory (errno=2)
RTAPI: ERROR: could not open shared memory (errno=2)
RTAPI: ERROR: could not open shared memory (errno=2)
RTAPI: ERROR: could not open shared memory (errno=2)
RTAPI: ERROR: could not open shared memory (errno=2)
RTAPI: ERROR: could not open shared memory (errno=2)
RTAPI: ERROR: could not open shared memory (errno=2)
RTAPI: ERROR: could not open shared memory (errno=2)
RTAPI requires the real-time kernel 2.6.32-122-rtai to run. Before running
this realtime application, reboot and choose this kernel at the boot menu.
Cleanup done
LinuxCNC terminated with an error. You can find more information in the log:
/home/maura/linuxcnc_debug.txt
and
/home/maura/linuxcnc_print.txt
as well as in the output of the shell command 'dmesg' and in the terminal
maura@ubuntu:~/linuxcnc-rtos$
thanks again
Re: Linuxcnc 2.5.2 won't run
Okay, try this then:
sudo apt-get remove -pruge rtai-modules-3.4.55-rtai-2_3.9-shabby-memleak
Then you'll need to reinstall linuxCNC.
Your errors above are because rtai was not fully installed.
Mark
Re: Linuxcnc 2.5.2 won't run
if -pruge doesnt work try -purge
Im guessing that was a typo.
Re: Linuxcnc 2.5.2 won't run
have you tried flatcam on the 10.04 livecd? I see it was tested on 12.04 but I didnt see anywhere that it is required.
Re: Linuxcnc 2.5.2 won't run
Hi Alan,
Thanks. I understood it to be purge from the start. I am getting still a syntax error. Please review;
maura@ubuntu:~$ sudo apt-get remove -purge rtai-modules-3.4.55-rtai-2_3.9-shabby-memleak
E: Command line option 'p' [from -purge] is not known.
Re: Linuxcnc 2.5.2 won't run
Hi again Alan,
No, but reading the install page of FlatCAM it required sub programs that I could not find on liveCD. It's a thought. Maybe I should reinstall everything from scratch with 10.04 and build from there.
This is what the install page says:
Ubuntu
Tested on Ubuntu 12.04 LTS.
Install python-gi
Install libgtk-3-devel
Install python-shapely
Install numpy, scipy and matplotlib
sudo apt-get install python-gi
sudo apt-get install libgtk-3-devel
sudo apt-get install python-shapely
sudo apt-get install python-numpy python-scipy python-matplotlib
Sometime matplotlib might complain about missing libraries, particularly backend_gtk3agg. Then installing from source can fix this:
sudo apt-get install python-pip
sudo pip install matplotlib
This might complain about missing the distribute package. Install it (and try again):
easy_install -U distribute
If Shapely complains about missing libraries do:
sudo apt-get install libgeos-dev
One other thing that has come up is the need to install the Python development package in order for binaries to be able to compile. Do:
sudo apt-get install python-dev
Finally download and uncompress the Source, switch to the uncompressed directory and run:
python FlatCAM.py
Re: Linuxcnc 2.5.2 won't run
Ach! Sorry about that. Bad info on the apt-get command. Try: "sudo apt-get purge rtai-modules-3.4.55-rtai-2_3.9-shabby-memleak", or "sudo dpkg --purge rtai-modules-3.4.55-rtai-2_3.9-shabby-memleak"
Mark
Re: Linuxcnc 2.5.2 won't run
Thanks. I'll try it shortly. I'm building another machine right now for Linux only. The other computer has a dual boot with Ubuntu and Win 7.
Hence I'll try a new install. I'll be careful to install everything right. I have gained a lot of experience with this installation.
Thanks again.
Re: Linuxcnc 2.5.2 won't run
Hi This Looks like you dont have real time Kernel build i recommend to cle an the build path and rebuild from scratch i had this error when i tried to build my own Kernel for a Mini Box ... the linuxcnc Forum was verry helpful Thomas
Gesendet von meinem SM-N9005 mit Tapatalk
Re: Linuxcnc 2.5.2 won't run
To load linuxcnc to ubuntu 12.04 need rtai kernel see:
LinuxCNC Documentation Wiki: LinuxCNC On Ubuntu Precise
This will let you load a rtai kernel under 12.04 lts and 2.6... linuxcnc
Regards