Re: Fagor 8020ms with Windnc
So ive figured out most of what i needed help with. I keep getting a Nr 255 error during the file transfer from WinDNC. Has anybody else had this error? I called and spoke with fagor and they were unable to tell me what it is. They will be contacting fagor in spain to see it anyone over there happens to know.
Re: Fagor 8020ms with Windnc
Arron,
Were you able to figure this file transfer problem out?
If so, what was the problem?
Just curious.
Thanks.
Regards,
Todd
Re: Fagor 8020ms with Windnc
I have figured it out for the most part. It was the post processor I was using. Now im getting ERROR 34 STRANGE CHARACTER errors and I have no idea where the problem lies. Ive gone over the code so many times and cant seem to find the problem. With that being said I want to make it clear that I know little to nothing about G code so the problem my be obvious and I just don't know what im looking for. Im trying to figure out how to load the post on here but the only way I can do it is to past it on here. Hope nobody minds the long code. If anyone can spot the error or errors (there may be a lot) please let me know.
%00001
N1 G90 G80 G70 G40 G17
N2 T1.1 M06
N3 S4000 M03
N4 G00 G90 G54 X-1.476 Y-1.45
N5 G43
N6
N7 Z0.2
N8 Z0.1
N9
N10 G01 Y-1.2512 F180.
N11 X-1.4942 Y-1.2435
N12 X-1.5289 Y-1.2267
N13 X-1.5627 Y-1.2083
N14 X-1.5955 Y-1.1882
N15 X-1.6273 Y-1.1665
N16 X-1.658 Y-1.1433
N17 X-1.6875 Y-1.1186
N18 X-1.7157 Y-1.0924
N19 X-1.7424 Y-1.0651
N20 X-1.9341 Y-1.1169
N21 G00 Z0.1
N22 Z0.2
N23 X1.9344 Y-1.1159
N24 Z-0.25
N25 G01 X1.7431 Y-1.0641 F180.
N26 X1.7247 Y-1.0836
N27 X1.6975 Y-1.1097
N28 X1.6841 Y-1.1213
N29 X1.671 Y-1.1323
N30 X1.6481 Y-1.1583
N31 X1.6239 Y-1.1831
N32 X1.5984 Y-1.2066
N33 X1.5717 Y-1.2287
N34 X1.5476 Y-1.2465
N35 X1.5863 Y-1.4412
N36 G00 Z0.1
N37 Z0.2
N38 X1.5137 Y1.4497
N39 Z-0.25
N40 G01 X1.5075 Y1.2511 F180.
N41 X1.5182 Y1.2437
N42 X1.5444 Y1.2229
N43 X1.5694 Y1.2007
N44 X1.5931 Y1.177
N45 X1.6154 Y1.152
N46 X1.6361 Y1.1257
N47 X1.6553 Y1.0983
N48 X1.6729 Y1.0698
N49 X1.6888 Y1.0403
N50 X1.703 Y1.01
N51 X1.7153 Y0.9789
N52 X1.7259 Y0.9471
N53 X1.7345 Y0.9147
N54 X1.7413 Y0.8819
N55 X1.7461 Y0.8488
N56 X1.7491 Y0.8155
N57 X1.75 Y0.782
N58 Y0.7745
N59 Y-0.5387
N60 X1.75 Y-0.5395
N61 X1.749 Y-0.5712
N62 X1.7462 Y-0.6028
N63 X1.7417 Y-0.6342
N64 X1.7355 Y-0.6653
N65 X1.7276 Y-0.696
N66 X1.718 Y-0.7262
N67 X1.7068 Y-0.7558
N68 X1.6939 Y-0.7848
N69 X1.6795 Y-0.813
N70 X1.6635 Y-0.8404
N71 X1.6461 Y-0.8669
N72 X1.6272 Y-0.8923
N73 X1.607 Y-0.9167
N74 X1.5854 Y-0.94
N75 X1.5626 Y-0.962
N76 X1.5559 Y-0.9678
N77 X1.5278 Y-0.9912
N78 X1.5093 Y-1.0136
N79 X1.4895 Y-1.0348
N80 X1.4683 Y-1.0547
N81 X1.4459 Y-1.0731
N82 X1.4224 Y-1.0901
N83 X1.3978 Y-1.1056
N84 X1.3723 Y-1.1194
N85 X1.3459 Y-1.1315
N86 X1.3188 Y-1.142
N87 X1.2911 Y-1.1507
N88 X1.2629 Y-1.1576
N89 X1.2343 Y-1.1626
N90 X1.2055 Y-1.1658
N91 X1.1957 Y-1.1664
N92 X1.1289 Y-1.1674
N93 X1.1043 Y-1.1672
N94 X1.1014
N95 X1.0746 Y-1.1668
N96 X1.0479 Y-1.1653
N97 X1.0301 Y-1.1632
N98 X1.0254 Y-1.1624
N99 X1.0098 Y-1.1645
N100 X0.9941 Y-1.166
N101 X0.9809 Y-1.1667
N102 X0.8961 Y-1.1674
N103 X0.8499 Y-1.1671
N104 X0.849
N105 X0.8217 Y-1.1663
N106 X0.7946 Y-1.1639
N107 X0.7676 Y-1.1599
N108 X0.741 Y-1.1542
N109 X0.7147 Y-1.147
N110 X0.6889 Y-1.1383
N111 X0.6636 Y-1.128
N112 X0.6575 Y-1.1252
N113 X0.6328 Y-1.1124
N114 X-1.1851 Y-1.1122
N115 X-1.1906 Y-1.1122
N116 X-1.2234 Y-1.1103
N117 X-1.2559 Y-1.1066
N118 X-1.2882 Y-1.1011
N119 X-1.3202 Y-1.0937
N120 X-1.3517 Y-1.0845
N121 X-1.3826 Y-1.0735
N122 X-1.4128 Y-1.0608
N123 X-1.4422 Y-1.0464
N124 X-1.4708 Y-1.0303
N125 X-1.4984 Y-1.0127
N126 X-1.525 Y-0.9934
N127 X-1.5504 Y-0.9727
N128 X-1.5746 Y-0.9506
N129 X-1.5975 Y-0.9272
N130 X-1.6191 Y-0.9025
N131 X-1.6392 Y-0.8766
N132 X-1.6577 Y-0.8495
N133 X-1.6748 Y-0.8215
N134 X-1.6902 Y-0.7926
N135 X-1.7039 Y-0.7628
N136 X-1.7159 Y-0.7323
N137 X-1.7261 Y-0.7011
N138 X-1.7346 Y-0.6695
N139 X-1.7412 Y-0.6373
N140 X-1.746 Y-0.6049
N141 X-1.7489 Y-0.5723
N142 X-1.75 Y-0.5395
N143 Y-0.5387
N144 Y0.7745
N145 X-1.75 Y0.7821
N146 X-1.7491 Y0.815
N147 X-1.7463 Y0.8477
N148 X-1.7416 Y0.8803
N149 X-1.7351 Y0.9125
N150 X-1.7267 Y0.9443
N151 X-1.7165 Y0.9756
N152 X-1.7046 Y1.0062
N153 X-1.6909 Y1.0361
N154 X-1.6756 Y1.0652
N155 X-1.6586 Y1.0933
N156 X-1.64 Y1.1205
N157 X-1.62 Y1.1465
N158 X-1.5984 Y1.1713
N159 X-1.5755 Y1.1949
N160 X-1.5513 Y1.2171
N161 X-1.5258 Y1.2379
N162 X-1.5079 Y1.2509
N163 X-1.5156 Y1.4493
N164 G00 Z0.1
N165 Z0.2
N166 X0.9581 Y-1.1673
N167 Z0.1
N168 G01 Z-0.25 F180.
N169 X1.0124 Y-1.0571
N170 X1.0143 Y-1.0526
N171 X1.016 Y-1.048
N172 X1.0172 Y-1.0433
N173 X1.0181 Y-1.0386
N174 X1.0186 Y-1.0337
N175 X1.0188 Y-1.0289
N176 X1.0185 Y-1.024
N177 X1.0179 Y-1.0192
N178 X1.0169 Y-1.0144
N179 X1.0156 Y-1.0098
N180 X1.0138 Y-1.0052
N181 X1.0118 Y-1.0008
N182 X1.0094 Y-0.9966
N183 X1.0066 Y-0.9926
N184 X1.0036 Y-0.9888
N185 X1.0003 Y-0.9852
N186 X0.9967 Y-0.982
N187 X0.9929 Y-0.979
N188 X0.9888 Y-0.9763
N189 X0.9846 Y-0.9739
N190 X0.9802 Y-0.9719
N191 X0.9756 Y-0.9702
N192 X0.9709 Y-0.9689
N193 X0.9662 Y-0.968
N194 X0.9613 Y-0.9674
N195 X0.9565 Y-0.9672
N196 X0.8505 Y-0.9671
N197 X0.8293 Y-0.9666
N198 X0.808 Y-0.964
N199 X0.8008 Y-0.9627
N200 X0.7868 Y-0.9597
N201 X0.7656 Y-0.9534
N202 X0.7444 Y-0.9451
N203 X0.7374 Y-0.9415
N204 X0.7232 Y-0.934
N205 X0.7019 Y-0.9203
N206 X0.6808 Y-0.9137
N207 X0.6596 Y-0.9124
N208 X-1.1639
N209 X-1.1851 Y-0.9122
N210 X-1.2063 Y-0.9111
N211 X-1.2275 Y-0.9086
N212 X-1.2487 Y-0.9051
N213 X-1.2699 Y-0.9002
N214 X-1.274 Y-0.8991
N215 X-1.2911 Y-0.8939
N216 X-1.3123 Y-0.8864
N217 X-1.3335 Y-0.8771
N218 X-1.3547 Y-0.8665
N219 X-1.3716 Y-0.8567
N220 X-1.3759 Y-0.854
N221 X-1.3971 Y-0.8394
N222 X-1.4024 Y-0.8355
N223 X-1.4183 Y-0.8227
N224 X-1.4277 Y-0.8143
N225 X-1.4395 Y-0.8032
N226 X-1.4492 Y-0.7931
N227 X-1.4607 Y-0.7802
N228 X-1.4677 Y-0.7719
N229 X-1.4819 Y-0.7527
N230 X-1.4834 Y-0.7507
N231 X-1.4969 Y-0.7295
N232 X-1.5031 Y-0.7188
N233 X-1.5088 Y-0.7083
N234 X-1.5187 Y-0.6871
N235 X-1.5244 Y-0.6737
N236 X-1.5272 Y-0.6659
N237 X-1.5343 Y-0.6447
N238 X-1.5398 Y-0.6235
N239 X-1.5443 Y-0.6023
N240 X-1.5456 Y-0.5944
N241 X-1.5474 Y-0.5811
N242 X-1.5492 Y-0.5599
N243 X-1.55 Y-0.5387
N244 Y0.776
N245 X-1.5496 Y0.7972
N246 X-1.5483 Y0.8184
N247 X-1.5456 Y0.8395
N248 X-1.5417 Y0.8608
N249 X-1.5365 Y0.882
N250 X-1.5299 Y0.9032
N251 X-1.5244 Y0.9188
N252 X-1.5221 Y0.9244
N253 X-1.5126 Y0.9456
N254 X-1.5031 Y0.9639
N255 X-1.5015 Y0.9668
N256 X-1.4887 Y0.988
N257 X-1.4819 Y0.9978
N258 X-1.4736 Y1.0092
N259 X-1.4607 Y1.0253
N260 X-1.4562 Y1.0304
N261 X-1.4395 Y1.0483
N262 X-1.4362 Y1.0516
N263 X-1.4183 Y1.0678
N264 X-1.4124 Y1.0728
N265 X-1.3971 Y1.0845
N266 X-1.3838 Y1.094
N267 X-1.3759 Y1.0992
N268 X-1.3547 Y1.1116
N269 X-1.3481 Y1.1152
N270 X-1.3335 Y1.1222
N271 X-1.3123 Y1.1315
N272 X-1.2987 Y1.1364
N273 X-1.2911 Y1.139
N274 X-1.2699 Y1.1453
N275 X-1.2487 Y1.1502
N276 X-1.2275 Y1.1537
N277 X-1.2063 Y1.1562
N278 X-1.1851 Y1.1573
N279 X-1.1639 Y1.1575
N280 X1.1685
N281 X1.1897 Y1.1571
N282 X1.2109 Y1.1558
N283 X1.2321 Y1.1531
N284 X1.2533 Y1.1492
N285 X1.2745 Y1.1441
N286 X1.2957 Y1.1374
N287 X1.2987 Y1.1364
N288 X1.3169 Y1.1296
N289 X1.3381 Y1.1201
N290 X1.3481 Y1.1152
N291 X1.3593 Y1.109
N292 X1.3805 Y1.0962
N293 X1.3838 Y1.094
N294 X1.4018 Y1.0811
N295 X1.4124 Y1.0728
N296 X1.423 Y1.0637
N297 X1.4362 Y1.0516
N298 X1.4442 Y1.0436
N299 X1.4562 Y1.0304
N300 X1.4654 Y1.0198
N301 X1.4736 Y1.0092
N302 X1.4866 Y0.9912
N303 X1.4887 Y0.988
N304 X1.5015 Y0.9668
N305 X1.5078 Y0.9554
N306 X1.5126 Y0.9456
N307 X1.5221 Y0.9244
N308 X1.529 Y0.9059
N309 X1.5299 Y0.9032
N310 X1.5366 Y0.882
N311 X1.5417 Y0.8608
N312 X1.5455 Y0.8396
N313 X1.5483 Y0.8184
N314 X1.5496 Y0.7972
N315 X1.55 Y0.776
N316 Y-0.5387
N317 X1.5492 Y-0.5599
N318 X1.5474 Y-0.5811
N319 X1.5443 Y-0.6023
N320 X1.5399 Y-0.6235
N321 X1.5343 Y-0.6447
N322 X1.529 Y-0.6609
N323 X1.5272 Y-0.6659
N324 X1.5188 Y-0.6871
N325 X1.5088 Y-0.7083
N326 X1.5078 Y-0.7103
N327 X1.497 Y-0.7295
N328 X1.4866 Y-0.7461
N329 X1.4834 Y-0.7507
N330 X1.4677 Y-0.7719
N331 X1.4654 Y-0.7747
N332 X1.4492 Y-0.7931
N333 X1.4442 Y-0.7985
N334 X1.4277 Y-0.8143
N335 X1.423 Y-0.8186
N336 X1.4024 Y-0.8355
N337 X1.3805 Y-0.8534
N338 X1.3784 Y-0.8567
N339 X1.3625 Y-0.8779
N340 X1.3593 Y-0.8815
N341 X1.3423 Y-0.8991
N342 X1.3381 Y-0.903
N343 X1.3166 Y-0.9203
N344 X1.2957 Y-0.9338
N345 X1.2809 Y-0.9415
N346 X1.2745 Y-0.9447
N347 X1.2533 Y-0.9532
N348 X1.2321 Y-0.9597
N349 X1.2174 Y-0.9627
N350 X1.2109 Y-0.9639
N351 X1.1897 Y-0.9665
N352 X1.1685 Y-0.9672
N353 X1.1049
N354 X1.0837 Y-0.9671
N355 X1.0625 Y-0.9658
N356 X1.0413 Y-0.9625
N357 X1.0201 Y-0.96
N358 X1.0073 Y-0.9627
N359 X0.9989 Y-0.9643
N360 X0.9777 Y-0.9667
N361 X0.9565 Y-0.9672
N362 G00 Z0.1
N363 Z0.2
N364 X-1.476 Y-1.45
N365 Z0.1
N366 Z-0.5
N367 G01 Y-1.2512 F180.
N368 X-1.4942 Y-1.2435
N369 X-1.5289 Y-1.2267
N370 X-1.5627 Y-1.2083
N371 X-1.5955 Y-1.1882
N372 X-1.6273 Y-1.1665
N373 X-1.658 Y-1.1433
N374 X-1.6875 Y-1.1186
N375 X-1.7157 Y-1.0924
N376 X-1.7424 Y-1.0651
N377 X-1.9341 Y-1.1169
N378 G00 Z-0.15
N379 X0.689 Y-1.45
N380 Z-0.5
N381 G01 Y-1.2516 F180.
N382 X0.6872 Y-1.2504
N383 X0.661 Y-1.2308
N384 X0.6359 Y-1.2097
N385 X0.6121 Y-1.1872
N386 X0.5896 Y-1.1635
N387 X0.5684 Y-1.1385
N388 X0.5486 Y-1.1124
N389 X-1.1851 Y-1.1122
N390 X-1.1906 Y-1.1122
N391 X-1.2234 Y-1.1103
N392 X-1.2559 Y-1.1066
N393 X-1.2882 Y-1.1011
N394 X-1.3202 Y-1.0937
N395 X-1.3517 Y-1.0845
N396 X-1.3826 Y-1.0735
N397 X-1.4128 Y-1.0608
N398 X-1.4422 Y-1.0464
N399 X-1.4708 Y-1.0303
N400 X-1.4984 Y-1.0127
N401 X-1.525 Y-0.9934
N402 X-1.5504 Y-0.9727
N403 X-1.5746 Y-0.9506
N404 X-1.5975 Y-0.9272
N405 X-1.6191 Y-0.9025
N406 X-1.6392 Y-0.8766
N407 X-1.6577 Y-0.8495
N408 X-1.6748 Y-0.8215
N409 X-1.6902 Y-0.7926
N410 X-1.7039 Y-0.7628
N411 X-1.7159 Y-0.7323
N412 X-1.7261 Y-0.7011
N413 X-1.7346 Y-0.6695
N414 X-1.7412 Y-0.6373
N415 X-1.746 Y-0.6049
N416 X-1.7489 Y-0.5723
N417 X-1.75 Y-0.5395
N418 Y-0.5387
N419 Y0.7745
N420 X-1.75 Y0.7821
N421 X-1.7491 Y0.815
N422 X-1.7463 Y0.8477
N423 X-1.7416 Y0.8803
N424 X-1.7351 Y0.9125
N425 X-1.7267 Y0.9443
N426 X-1.7165 Y0.9756
N427 X-1.7046 Y1.0062
N428 X-1.6909 Y1.0361
N429 X-1.6756 Y1.0652
N430 X-1.6586 Y1.0933
N431 X-1.64 Y1.1205
N432 X-1.62 Y1.1465
N433 X-1.5984 Y1.1713
N434 X-1.5755 Y1.1949
N435 X-1.5513 Y1.2171
N436 X-1.5258 Y1.2379
N437 X-1.5079 Y1.2509
N438 X-1.5156 Y1.4493
N439 G00 Z-0.15
N440 Z-0.05
N441 Z0.2
N442 X1.5137 Y1.4497
N443 Z0.1
N444 Z-0.5
N445 G01 X1.5075 Y1.2511 F180.
N446 X1.5182 Y1.2437
N447 X1.5444 Y1.2229
N448 X1.5694 Y1.2007
N449 X1.5931 Y1.177
N450 X1.6154 Y1.152
N451 X1.6361 Y1.1257
N452 X1.6553 Y1.0983
N453 X1.6729 Y1.0698
N454 X1.6888 Y1.0403
N455 X1.703 Y1.01
N456 X1.7153 Y0.9789
N457 X1.7259 Y0.9471
N458 X1.7345 Y0.9147
N459 X1.7413 Y0.8819
N460 X1.7461 Y0.8488
N461 X1.7491 Y0.8155
N462 X1.75 Y0.782
N463 Y0.7745
N464 Y-0.5387
N465 X1.75 Y-0.5396
N466 X1.7489 Y-0.5726
N467 X1.7459 Y-0.6054
N468 X1.741 Y-0.6381
N469 X1.7343 Y-0.6704
N470 X1.7258 Y-0.7023
N471 X1.7154 Y-0.7336
N472 X1.7032 Y-0.7643
N473 X1.6893 Y-0.7942
N474 X1.6737 Y-0.8233
N475 X1.6565 Y-0.8515
N476 X1.6377 Y-0.8786
N477 X1.6173 Y-0.9046
N478 X1.5955 Y-0.9294
N479 X1.5918 Y-0.9333
N480 X1.5858 Y-0.9394
N481 X1.5751 Y-0.9718
N482 X1.5626 Y-1.0035
N483 X1.5482 Y-1.0344
N484 X1.5321 Y-1.0644
N485 X1.5143 Y-1.0935
N486 X1.4948 Y-1.1214
N487 X1.4737 Y-1.1482
N488 X1.451 Y-1.1737
N489 X1.427 Y-1.1978
N490 X1.4015 Y-1.2205
N491 X1.3748 Y-1.2417
N492 X1.3605 Y-1.2518
N493 Y-1.45
N494 G00 Z-0.15
N495 Z-0.05
N496 Z0.2
N497 X1.0413
N498 Z0.1
N499 Z-0.5
N500 G01 Y-1.1575 F180.
N501 X1.0201 Y-1.158
N502 X0.9989 Y-1.157
N503 X0.9777 Y-1.155
N504 X0.9674 Y-1.1536
N505 X0.9565 Y-1.1518
N506 X0.9353 Y-1.1473
N507 X0.9141 Y-1.1417
N508 X0.8929 Y-1.1345
N509 X0.8869 Y-1.1324
N510 X0.8717 Y-1.1261
N511 X0.8505 Y-1.1162
N512 X0.841 Y-1.1112
N513 X0.8293 Y-1.1044
N514 X0.808 Y-1.091
N515 X0.7868 Y-1.0755
N516 X0.7786 Y-1.0688
N517 X0.7656 Y-1.0574
N518 X0.7551 Y-1.0475
N519 X0.7444 Y-1.0365
N520 X0.7351 Y-1.0263
N521 X0.7232 Y-1.0121
N522 X0.718 Y-1.0051
N523 X0.703 Y-0.9839
N524 X0.702 Y-0.9824
N525 X0.69 Y-0.9627
N526 X0.6808 Y-0.9455
N527 X0.6789 Y-0.9415
N528 X0.6658 Y-0.9124
N529 X-1.1639
N530 X-1.1851 Y-0.9122
N531 X-1.2063 Y-0.9111
N532 X-1.2275 Y-0.9086
N533 X-1.2487 Y-0.9051
N534 X-1.2699 Y-0.9002
N535 X-1.274 Y-0.8991
N536 X-1.2911 Y-0.8939
N537 X-1.3123 Y-0.8864
N538 X-1.3335 Y-0.8771
N539 X-1.3547 Y-0.8665
N540 X-1.3716 Y-0.8567
N541 X-1.3759 Y-0.854
N542 X-1.3971 Y-0.8394
N543 X-1.4024 Y-0.8355
N544 X-1.4183 Y-0.8227
N545 X-1.4277 Y-0.8143
N546 X-1.4395 Y-0.8032
N547 X-1.4492 Y-0.7931
N548 X-1.4607 Y-0.7802
N549 X-1.4677 Y-0.7719
N550 X-1.4834 Y-0.7507
N551 X-1.4969 Y-0.7295
N552 X-1.5031 Y-0.7188
N553 X-1.5088 Y-0.7083
N554 X-1.5187 Y-0.6871
N555 X-1.5244 Y-0.6737
N556 X-1.5272 Y-0.6659
N557 X-1.5343 Y-0.6447
N558 X-1.5398 Y-0.6235
N559 X-1.5443 Y-0.6023
N560 X-1.5456 Y-0.5944
N561 X-1.5474 Y-0.5811
N562 X-1.5492 Y-0.5599
N563 X-1.55 Y-0.5387
N564 Y0.776
N565 X-1.5496 Y0.7972
N566 X-1.5483 Y0.8184
N567 X-1.5456 Y0.8395
N568 X-1.5417 Y0.8608
N569 X-1.5365 Y0.882
N570 X-1.5299 Y0.9032
N571 X-1.5244 Y0.9188
N572 X-1.5221 Y0.9244
N573 X-1.5126 Y0.9456
N574 X-1.5031 Y0.9639
N575 X-1.5015 Y0.9668
N576 X-1.4887 Y0.988
N577 X-1.4819 Y0.9978
N578 X-1.4736 Y1.0092
N579 X-1.4607 Y1.0253
N580 X-1.4562 Y1.0304
N581 X-1.4395 Y1.0483
N582 X-1.4362 Y1.0516
N583 X-1.4183 Y1.0678
N584 X-1.4124 Y1.0728
N585 X-1.3971 Y1.0845
N586 X-1.3838 Y1.094
N587 X-1.3759 Y1.0992
N588 X-1.3547 Y1.1116
N589 X-1.3481 Y1.1152
N590 X-1.3335 Y1.1222
N591 X-1.3123 Y1.1315
N592 X-1.2987 Y1.1364
N593 X-1.2911 Y1.139
N594 X-1.2699 Y1.1453
N595 X-1.2487 Y1.1502
N596 X-1.2275 Y1.1537
N597 X-1.2063 Y1.1562
N598 X-1.1851 Y1.1573
N599 X-1.1639 Y1.1575
N600 X1.1685
N601 X1.1897 Y1.1571
N602 X1.2109 Y1.1558
N603 X1.2321 Y1.1531
N604 X1.2533 Y1.1492
N605 X1.2745 Y1.1441
N606 X1.2957 Y1.1374
N607 X1.2987 Y1.1364
N608 X1.3169 Y1.1296
N609 X1.3381 Y1.1201
N610 X1.3481 Y1.1152
N611 X1.3593 Y1.109
N612 X1.3805 Y1.0962
N613 X1.3838 Y1.094
N614 X1.4018 Y1.0811
N615 X1.4124 Y1.0728
N616 X1.423 Y1.0637
N617 X1.4362 Y1.0516
N618 X1.4442 Y1.0436
N619 X1.4562 Y1.0304
N620 X1.4654 Y1.0198
N621 X1.4736 Y1.0092
N622 X1.4866 Y0.9912
N623 X1.4887 Y0.988
N624 X1.5015 Y0.9668
N625 X1.5078 Y0.9554
N626 X1.5126 Y0.9456
N627 X1.5221 Y0.9244
N628 X1.529 Y0.9059
N629 X1.5299 Y0.9032
N630 X1.5366 Y0.882
N631 X1.5417 Y0.8608
N632 X1.5455 Y0.8396
N633 X1.5483 Y0.8184
N634 X1.5496 Y0.7972
N635 X1.55 Y0.776
N636 Y-0.5387
N637 X1.5492 Y-0.5599
N638 X1.5474 Y-0.5811
N639 X1.5443 Y-0.6023
N640 X1.5399 Y-0.6235
N641 X1.5343 Y-0.6447
N642 X1.529 Y-0.6609
N643 X1.5272 Y-0.6659
N644 X1.5188 Y-0.6871
N645 X1.5088 Y-0.7083
N646 X1.5078 Y-0.7103
N647 X1.497 Y-0.7295
N648 X1.4866 Y-0.7461
N649 X1.4834 Y-0.7507
N650 X1.4677 Y-0.7719
N651 X1.4654 Y-0.7747
N652 X1.4492 Y-0.7931
N653 X1.4442 Y-0.7985
N654 X1.4278 Y-0.8143
N655 X1.423 Y-0.8186
N656 X1.4049 Y-0.8355
N657 X1.4018 Y-0.8518
N658 X1.4007 Y-0.8567
N659 X1.3953 Y-0.8779
N660 X1.3887 Y-0.8991
N661 X1.3807 Y-0.9203
N662 X1.3711 Y-0.9415
N663 X1.3593 Y-0.9638
N664 X1.347 Y-0.9839
N665 X1.3381 Y-0.9969
N666 X1.3321 Y-1.0051
N667 X1.3169 Y-1.0239
N668 X1.3149 Y-1.0263
N669 X1.2948 Y-1.0475
N670 X1.2745 Y-1.066
N671 X1.2713 Y-1.0688
N672 X1.2533 Y-1.083
N673 X1.2433 Y-1.09
N674 X1.2321 Y-1.0975
N675 X1.2109 Y-1.11
N676 X1.2088 Y-1.1112
N677 X1.1897 Y-1.121
N678 X1.1685 Y-1.1302
N679 X1.1631 Y-1.1324
N680 X1.1473 Y-1.1379
N681 X1.1261 Y-1.1445
N682 X1.1049 Y-1.1495
N683 X1.0837 Y-1.1535
N684 X1.0625 Y-1.1562
N685 X1.0413 Y-1.1575
N686 G00 Z-0.15
N687 Z-0.05
N688 Z0.2
N689 X-1.476 Y-1.45
N690 Z-0.15
N691 Z-0.75
N692 G01 Y-1.2512 F180.
N693 X-1.4942 Y-1.2435
N694 X-1.5289 Y-1.2267
N695 X-1.5627 Y-1.2083
N696 X-1.5955 Y-1.1882
N697 X-1.6273 Y-1.1665
N698 X-1.658 Y-1.1433
N699 X-1.6875 Y-1.1186
N700 X-1.7157 Y-1.0924
N701 X-1.7424 Y-1.0651
N702 X-1.9341 Y-1.1169
N703 G00 Z-0.4
N704 X0.689 Y-1.45
N705 Z-0.75
N706 G01 Y-1.2516 F180.
N707 X0.6872 Y-1.2504
N708 X0.661 Y-1.2308
N709 X0.636 Y-1.2097
N710 X0.6121 Y-1.1872
N711 X0.5896 Y-1.1635
N712 X0.5684 Y-1.1385
N713 X0.5487 Y-1.1124
N714 X-1.1851 Y-1.1122
N715 X-1.1906 Y-1.1122
N716 X-1.2234 Y-1.1103
N717 X-1.2559 Y-1.1066
N718 X-1.2882 Y-1.1011
N719 X-1.3202 Y-1.0937
N720 X-1.3517 Y-1.0845
N721 X-1.3826 Y-1.0735
N722 X-1.4128 Y-1.0608
N723 X-1.4422 Y-1.0464
N724 X-1.4708 Y-1.0303
N725 X-1.4984 Y-1.0127
N726 X-1.525 Y-0.9934
N727 X-1.5504 Y-0.9727
N728 X-1.5746 Y-0.9506
N729 X-1.5975 Y-0.9272
N730 X-1.6191 Y-0.9025
N731 X-1.6392 Y-0.8766
N732 X-1.6577 Y-0.8495
N733 X-1.6748 Y-0.8215
N734 X-1.6902 Y-0.7926
N735 X-1.7039 Y-0.7628
N736 X-1.7159 Y-0.7323
N737 X-1.7261 Y-0.7011
N738 X-1.7346 Y-0.6695
N739 X-1.7412 Y-0.6373
N740 X-1.746 Y-0.6049
N741 X-1.7489 Y-0.5723
N742 X-1.75 Y-0.5395
N743 Y-0.5387
N744 Y0.7745
N745 X-1.75 Y0.7821
N746 X-1.7491 Y0.815
N747 X-1.7463 Y0.8477
N748 X-1.7416 Y0.8803
N749 X-1.7351 Y0.9125
N750 X-1.7267 Y0.9443
N751 X-1.7165 Y0.9756
N752 X-1.7046 Y1.0062
N753 X-1.6909 Y1.0361
N754 X-1.6756 Y1.0652
N755 X-1.6586 Y1.0933
N756 X-1.64 Y1.1205
N757 X-1.62 Y1.1465
N758 X-1.5984 Y1.1713
N759 X-1.5755 Y1.1949
N760 X-1.5513 Y1.2171
N761 X-1.5258 Y1.2379
N762 X-1.5079 Y1.2509
N763 X-1.5156 Y1.4493
N764 G00 Z-0.4
N765 Z-0.3
N766 Z0.2
N767 X1.5137 Y1.4497
N768 Z-0.15
N769 Z-0.75
N770 G01 X1.5075 Y1.2511 F180.
N771 X1.5182 Y1.2437
N772 X1.5444 Y1.2229
N773 X1.5694 Y1.2007
N774 X1.5931 Y1.177
N775 X1.6154 Y1.152
N776 X1.6361 Y1.1257
N777 X1.6553 Y1.0983
N778 X1.6729 Y1.0698
N779 X1.6888 Y1.0403
N780 X1.703 Y1.01
N781 X1.7153 Y0.9789
N782 X1.7259 Y0.9471
N783 X1.7345 Y0.9147
N784 X1.7413 Y0.8819
N785 X1.7461 Y0.8488
N786 X1.7491 Y0.8155
N787 X1.75 Y0.782
N788 Y0.7745
N789 Y-0.5387
N790 X1.75 Y-0.5396
N791 X1.7489 Y-0.5725
N792 X1.7459 Y-0.6054
N793 X1.7411 Y-0.6381
N794 X1.7343 Y-0.6704
N795 X1.7258 Y-0.7023
N796 X1.7154 Y-0.7336
N797 X1.7032 Y-0.7643
N798 X1.6893 Y-0.7943
N799 X1.6737 Y-0.8233
N800 X1.6565 Y-0.8515
N801 X1.6377 Y-0.8786
N802 X1.6173 Y-0.9046
N803 X1.5955 Y-0.9294
N804 X1.5918 Y-0.9333
N805 X1.5857 Y-0.9395
N806 X1.5755 Y-0.9706
N807 X1.5635 Y-1.0012
N808 X1.5498 Y-1.0311
N809 X1.5345 Y-1.0601
N810 X1.5176 Y-1.0882
N811 X1.4992 Y-1.1154
N812 X1.4792 Y-1.1414
N813 X1.4579 Y-1.1663
N814 X1.4352 Y-1.19
N815 X1.4349 Y-1.1903
N816 X1.4111 Y-1.2124
N817 X1.3861 Y-1.2331
N818 X1.3609 Y-1.2518
N819 Y-1.45
N820 G00 Z-0.4
N821 Z-0.3
N822 Z0.2
N823 X1.0413
N824 Z-0.15
N825 Z-0.75
N826 G01 Y-1.1575 F180.
N827 X1.0201 Y-1.158
N828 X0.9989 Y-1.1571
N829 X0.9777 Y-1.155
N830 X0.9673 Y-1.1536
N831 X0.9565 Y-1.1518
N832 X0.9353 Y-1.1473
N833 X0.9141 Y-1.1417
N834 X0.8929 Y-1.1346
N835 X0.8868 Y-1.1324
N836 X0.8717 Y-1.1261
N837 X0.8505 Y-1.1162
N838 X0.841 Y-1.1112
N839 X0.8293 Y-1.1044
N840 X0.808 Y-1.091
N841 X0.7868 Y-1.0755
N842 X0.7786 Y-1.0688
N843 X0.7656 Y-1.0575
N844 X0.7551 Y-1.0475
N845 X0.7444 Y-1.0365
N846 X0.7351 Y-1.0263
N847 X0.7232 Y-1.0121
N848 X0.718 Y-1.0051
N849 X0.703 Y-0.9839
N850 X0.702 Y-0.9824
N851 X0.69 Y-0.9627
N852 X0.6808 Y-0.9455
N853 X0.6789 Y-0.9415
N854 X0.6658 Y-0.9124
N855 X-1.1639
N856 X-1.1851 Y-0.9122
N857 X-1.2063 Y-0.9111
N858 X-1.2275 Y-0.9086
N859 X-1.2487 Y-0.9051
N860 X-1.2699 Y-0.9002
N861 X-1.274 Y-0.8991
N862 X-1.2911 Y-0.8939
N863 X-1.3123 Y-0.8864
N864 X-1.3335 Y-0.8771
N865 X-1.3547 Y-0.8665
N866 X-1.3716 Y-0.8567
N867 X-1.3759 Y-0.854
N868 X-1.3971 Y-0.8394
N869 X-1.4024 Y-0.8355
N870 X-1.4183 Y-0.8227
N871 X-1.4277 Y-0.8143
N872 X-1.4395 Y-0.8032
N873 X-1.4492 Y-0.7931
N874 X-1.4607 Y-0.7802
N875 X-1.4677 Y-0.7719
N876 X-1.4834 Y-0.7507
N877 X-1.4969 Y-0.7295
N878 X-1.5031 Y-0.7188
N879 X-1.5088 Y-0.7083
N880 X-1.5187 Y-0.6871
N881 X-1.5244 Y-0.6737
N882 X-1.5272 Y-0.6659
N883 X-1.5343 Y-0.6447
N884 X-1.5398 Y-0.6235
N885 X-1.5443 Y-0.6023
N886 X-1.5456 Y-0.5944
N887 X-1.5474 Y-0.5811
N888 X-1.5492 Y-0.5599
N889 X-1.55 Y-0.5387
N890 Y0.776
N891 X-1.5496 Y0.7972
N892 X-1.5483 Y0.8184
N893 X-1.5456 Y0.8395
N894 X-1.5417 Y0.8608
N895 X-1.5365 Y0.882
N896 X-1.5299 Y0.9032
N897 X-1.5244 Y0.9188
N898 X-1.5221 Y0.9244
N899 X-1.5126 Y0.9456
N900 X-1.5031 Y0.9639
N901 X-1.5015 Y0.9668
N902 X-1.4887 Y0.988
N903 X-1.4819 Y0.9978
N904 X-1.4736 Y1.0092
N905 X-1.4607 Y1.0253
N906 X-1.4562 Y1.0304
N907 X-1.4395 Y1.0483
N908 X-1.4362 Y1.0516
N909 X-1.4183 Y1.0678
N910 X-1.4124 Y1.0728
N911 X-1.3971 Y1.0845
N912 X-1.3838 Y1.094
N913 X-1.3759 Y1.0992
N914 X-1.3547 Y1.1116
N915 X-1.3481 Y1.1152
N916 X-1.3335 Y1.1222
N917 X-1.3123 Y1.1315
N918 X-1.2987 Y1.1364
N919 X-1.2911 Y1.139
N920 X-1.2699 Y1.1453
N921 X-1.2487 Y1.1502
N922 X-1.2275 Y1.1537
N923 X-1.2063 Y1.1562
N924 X-1.1851 Y1.1573
N925 X-1.1639 Y1.1575
N926 X1.1685
N927 X1.1897 Y1.1571
N928 X1.2109 Y1.1558
N929 X1.2321 Y1.1531
N930 X1.2533 Y1.1492
N931 X1.2745 Y1.1441
N932 X1.2957 Y1.1374
N933 X1.2987 Y1.1364
N934 X1.3169 Y1.1296
N935 X1.3381 Y1.1201
N936 X1.3481 Y1.1152
N937 X1.3593 Y1.109
N938 X1.3805 Y1.0962
N939 X1.3838 Y1.094
N940 X1.4018 Y1.0811
N941 X1.4124 Y1.0728
N942 X1.423 Y1.0637
N943 X1.4362 Y1.0516
N944 X1.4442 Y1.0436
N945 X1.4562 Y1.0304
N946 X1.4654 Y1.0198
N947 X1.4736 Y1.0092
N948 X1.4866 Y0.9912
N949 X1.4887 Y0.988
N950 X1.5015 Y0.9668
N951 X1.5078 Y0.9554
N952 X1.5126 Y0.9456
N953 X1.5221 Y0.9244
N954 X1.529 Y0.9059
N955 X1.5299 Y0.9032
N956 X1.5366 Y0.882
N957 X1.5417 Y0.8608
N958 X1.5455 Y0.8396
N959 X1.5483 Y0.8184
N960 X1.5496 Y0.7972
N961 X1.55 Y0.776
N962 Y-0.5387
N963 X1.5492 Y-0.5599
N964 X1.5474 Y-0.5811
N965 X1.5443 Y-0.6023
N966 X1.5399 Y-0.6235
N967 X1.5343 Y-0.6447
N968 X1.529 Y-0.6609
N969 X1.5272 Y-0.6659
N970 X1.5188 Y-0.6871
N971 X1.5088 Y-0.7083
N972 X1.5078 Y-0.7103
N973 X1.497 Y-0.7295
N974 X1.4866 Y-0.7461
N975 X1.4834 Y-0.7507
N976 X1.4677 Y-0.7719
N977 X1.4654 Y-0.7747
N978 X1.4492 Y-0.7931
N979 X1.4442 Y-0.7985
N980 X1.4278 Y-0.8143
N981 X1.423 Y-0.8186
N982 X1.4049 Y-0.8355
N983 X1.4018 Y-0.8518
N984 X1.4007 Y-0.8567
N985 X1.3954 Y-0.8779
N986 X1.3887 Y-0.8991
N987 X1.3807 Y-0.9203
N988 X1.3711 Y-0.9415
N989 X1.3593 Y-0.9638
N990 X1.347 Y-0.9839
N991 X1.3381 Y-0.9969
N992 X1.3321 Y-1.0051
N993 X1.3169 Y-1.0239
N994 X1.3149 Y-1.0263
N995 X1.2948 Y-1.0475
N996 X1.2745 Y-1.066
N997 X1.2713 Y-1.0688
N998 X1.2533 Y-1.083
N999 X1.2433 Y-1.09
N1000 X1.2321 Y-1.0975
N1001 X1.2109 Y-1.11
N1002 X1.2088 Y-1.1112
N1003 X1.1897 Y-1.121
N1004 X1.1685 Y-1.1302
N1005 X1.1631 Y-1.1324
N1006 X1.1473 Y-1.138
N1007 X1.1261 Y-1.1445
N1008 X1.1049 Y-1.1495
N1009 X1.0837 Y-1.1535
N1010 X1.0625 Y-1.1562
N1011 X1.0413 Y-1.1575
N1012 G00 Z-0.4
N1013 Z-0.3
N1014 Z0.2
N1015 X-1.476 Y-1.45
N1016 Z-0.16
N1017 Z-0.76
N1018 G01 Y-1.2512 F180.
N1019 X-1.4942 Y-1.2435
N1020 X-1.5289 Y-1.2267
N1021 X-1.5627 Y-1.2083
N1022 X-1.5955 Y-1.1882
N1023 X-1.6273 Y-1.1665
N1024 X-1.658 Y-1.1433
N1025 X-1.6875 Y-1.1186
N1026 X-1.7157 Y-1.0924
N1027 X-1.7424 Y-1.0651
N1028 X-1.9341 Y-1.1169
N1029 G00 Z-0.41
N1030 X0.689 Y-1.45
N1031 Z-0.76
N1032 G01 Y-1.2516 F180.
N1033 X0.6872 Y-1.2504
N1034 X0.661 Y-1.2308
N1035 X0.636 Y-1.2097
N1036 X0.6121 Y-1.1872
N1037 X0.5896 Y-1.1635
N1038 X0.5684 Y-1.1385
N1039 X0.5487 Y-1.1124
N1040 X-1.1851 Y-1.1122
N1041 X-1.1906 Y-1.1122
N1042 X-1.2234 Y-1.1103
N1043 X-1.2559 Y-1.1066
N1044 X-1.2882 Y-1.1011
N1045 X-1.3202 Y-1.0937
N1046 X-1.3517 Y-1.0845
N1047 X-1.3826 Y-1.0735
N1048 X-1.4128 Y-1.0608
N1049 X-1.4422 Y-1.0464
N1050 X-1.4708 Y-1.0303
N1051 X-1.4984 Y-1.0127
N1052 X-1.525 Y-0.9934
N1053 X-1.5504 Y-0.9727
N1054 X-1.5746 Y-0.9506
N1055 X-1.5975 Y-0.9272
N1056 X-1.6191 Y-0.9025
N1057 X-1.6392 Y-0.8766
N1058 X-1.6577 Y-0.8495
N1059 X-1.6748 Y-0.8215
N1060 X-1.6902 Y-0.7926
N1061 X-1.7039 Y-0.7628
N1062 X-1.7159 Y-0.7323
N1063 X-1.7261 Y-0.7011
N1064 X-1.7346 Y-0.6695
N1065 X-1.7412 Y-0.6373
N1066 X-1.746 Y-0.6049
N1067 X-1.7489 Y-0.5723
N1068 X-1.75 Y-0.5395
N1069 Y-0.5387
N1070 Y0.7745
N1071 X-1.75 Y0.7821
N1072 X-1.7491 Y0.815
N1073 X-1.7463 Y0.8477
N1074 X-1.7416 Y0.8803
N1075 X-1.7351 Y0.9125
N1076 X-1.7267 Y0.9443
N1077 X-1.7165 Y0.9756
N1078 X-1.7046 Y1.0062
N1079 X-1.6909 Y1.0361
N1080 X-1.6756 Y1.0652
N1081 X-1.6586 Y1.0933
N1082 X-1.64 Y1.1205
N1083 X-1.62 Y1.1465
N1084 X-1.5984 Y1.1713
N1085 X-1.5755 Y1.1949
N1086 X-1.5513 Y1.2171
N1087 X-1.5258 Y1.2379
N1088 X-1.5079 Y1.2509
N1089 X-1.5156 Y1.4493
N1090 G00 Z-0.41
N1091 Z-0.31
N1092 Z0.2
N1093 X1.5137 Y1.4497
N1094 Z-0.16
N1095 Z-0.76
N1096 G01 X1.5075 Y1.2511 F180.
N1097 X1.5182 Y1.2437
N1098 X1.5444 Y1.2229
N1099 X1.5694 Y1.2007
N1100 X1.5931 Y1.177
N1101 X1.6154 Y1.152
N1102 X1.6361 Y1.1257
N1103 X1.6553 Y1.0983
N1104 X1.6729 Y1.0698
N1105 X1.6888 Y1.0403
N1106 X1.703 Y1.01
N1107 X1.7153 Y0.9789
N1108 X1.7259 Y0.9471
N1109 X1.7345 Y0.9147
N1110 X1.7413 Y0.8819
N1111 X1.7461 Y0.8488
N1112 X1.7491 Y0.8155
N1113 X1.75 Y0.782
N1114 Y0.7745
N1115 Y-0.5387
N1116 X1.75 Y-0.5396
N1117 X1.7489 Y-0.5725
N1118 X1.7459 Y-0.6054
N1119 X1.7411 Y-0.6381
N1120 X1.7343 Y-0.6704
N1121 X1.7258 Y-0.7023
N1122 X1.7154 Y-0.7336
N1123 X1.7032 Y-0.7643
N1124 X1.6893 Y-0.7943
N1125 X1.6737 Y-0.8233
N1126 X1.6565 Y-0.8515
N1127 X1.6377 Y-0.8786
N1128 X1.6173 Y-0.9046
N1129 X1.5955 Y-0.9294
N1130 X1.5918 Y-0.9333
N1131 X1.5857 Y-0.9395
N1132 X1.5755 Y-0.9706
N1133 X1.5635 Y-1.0012
N1134 X1.5498 Y-1.0311
N1135 X1.5345 Y-1.0601
N1136 X1.5176 Y-1.0882
N1137 X1.4992 Y-1.1154
N1138 X1.4792 Y-1.1414
N1139 X1.4579 Y-1.1663
N1140 X1.4352 Y-1.19
N1141 X1.4349 Y-1.1903
N1142 X1.4111 Y-1.2124
N1143 X1.3861 Y-1.2331
N1144 X1.3609 Y-1.2518
N1145 Y-1.45
N1146 G00 Z-0.41
N1147 Z-0.31
N1148 Z0.2
N1149 X1.0413
N1150 Z-0.16
N1151 Z-0.76
N1152 G01 Y-1.1575 F180.
N1153 X1.0201 Y-1.158
N1154 X0.9989 Y-1.1571
N1155 X0.9777 Y-1.155
N1156 X0.9673 Y-1.1536
N1157 X0.9565 Y-1.1518
N1158 X0.9353 Y-1.1473
N1159 X0.9141 Y-1.1417
N1160 X0.8929 Y-1.1346
N1161 X0.8868 Y-1.1324
N1162 X0.8717 Y-1.1261
N1163 X0.8505 Y-1.1162
N1164 X0.841 Y-1.1112
N1165 X0.8293 Y-1.1044
N1166 X0.808 Y-1.091
N1167 X0.7868 Y-1.0755
N1168 X0.7786 Y-1.0688
N1169 X0.7656 Y-1.0575
N1170 X0.7551 Y-1.0475
N1171 X0.7444 Y-1.0365
N1172 X0.7351 Y-1.0263
N1173 X0.7232 Y-1.0121
N1174 X0.718 Y-1.0051
N1175 X0.703 Y-0.9839
N1176 X0.702 Y-0.9824
N1177 X0.69 Y-0.9627
N1178 X0.6808 Y-0.9455
N1179 X0.6789 Y-0.9415
N1180 X0.6658 Y-0.9124
N1181 X-1.1639
N1182 X-1.1851 Y-0.9122
N1183 X-1.2063 Y-0.9111
N1184 X-1.2275 Y-0.9086
N1185 X-1.2487 Y-0.9051
N1186 X-1.2699 Y-0.9002
N1187 X-1.274 Y-0.8991
N1188 X-1.2911 Y-0.8939
N1189 X-1.3123 Y-0.8864
N1190 X-1.3335 Y-0.8771
N1191 X-1.3547 Y-0.8665
N1192 X-1.3716 Y-0.8567
N1193 X-1.3759 Y-0.854
N1194 X-1.3971 Y-0.8394
N1195 X-1.4024 Y-0.8355
N1196 X-1.4183 Y-0.8227
N1197 X-1.4277 Y-0.8143
N1198 X-1.4395 Y-0.8032
N1199 X-1.4492 Y-0.7931
N1200 X-1.4607 Y-0.7802
N1201 X-1.4677 Y-0.7719
N1202 X-1.4834 Y-0.7507
N1203 X-1.4969 Y-0.7295
N1204 X-1.5031 Y-0.7188
N1205 X-1.5088 Y-0.7083
N1206 X-1.5187 Y-0.6871
N1207 X-1.5244 Y-0.6737
N1208 X-1.5272 Y-0.6659
N1209 X-1.5343 Y-0.6447
N1210 X-1.5398 Y-0.6235
N1211 X-1.5443 Y-0.6023
N1212 X-1.5456 Y-0.5944
N1213 X-1.5474 Y-0.5811
N1214 X-1.5492 Y-0.5599
N1215 X-1.55 Y-0.5387
N1216 Y0.776
N1217 X-1.5496 Y0.7972
N1218 X-1.5483 Y0.8184
N1219 X-1.5456 Y0.8395
N1220 X-1.5417 Y0.8608
N1221 X-1.5365 Y0.882
N1222 X-1.5299 Y0.9032
N1223 X-1.5244 Y0.9188
N1224 X-1.5221 Y0.9244
N1225 X-1.5126 Y0.9456
N1226 X-1.5031 Y0.9639
N1227 X-1.5015 Y0.9668
N1228 X-1.4887 Y0.988
N1229 X-1.4819 Y0.9978
N1230 X-1.4736 Y1.0092
N1231 X-1.4607 Y1.0253
N1232 X-1.4562 Y1.0304
N1233 X-1.4395 Y1.0483
N1234 X-1.4362 Y1.0516
N1235 X-1.4183 Y1.0678
N1236 X-1.4124 Y1.0728
N1237 X-1.3971 Y1.0845
N1238 X-1.3838 Y1.094
N1239 X-1.3759 Y1.0992
N1240 X-1.3547 Y1.1116
N1241 X-1.3481 Y1.1152
N1242 X-1.3335 Y1.1222
N1243 X-1.3123 Y1.1315
N1244 X-1.2987 Y1.1364
N1245 X-1.2911 Y1.139
N1246 X-1.2699 Y1.1453
N1247 X-1.2487 Y1.1502
N1248 X-1.2275 Y1.1537
N1249 X-1.2063 Y1.1562
N1250 X-1.1851 Y1.1573
N1251 X-1.1639 Y1.1575
N1252 X1.1685
N1253 X1.1897 Y1.1571
N1254 X1.2109 Y1.1558
N1255 X1.2321 Y1.1531
N1256 X1.2533 Y1.1492
N1257 X1.2745 Y1.1441
N1258 X1.2957 Y1.1374
N1259 X1.2987 Y1.1364
N1260 X1.3169 Y1.1296
N1261 X1.3381 Y1.1201
N1262 X1.3481 Y1.1152
N1263 X1.3593 Y1.109
N1264 X1.3805 Y1.0962
N1265 X1.3838 Y1.094
N1266 X1.4018 Y1.0811
N1267 X1.4124 Y1.0728
N1268 X1.423 Y1.0637
N1269 X1.4362 Y1.0516
N1270 X1.4442 Y1.0436
N1271 X1.4562 Y1.0304
N1272 X1.4654 Y1.0198
N1273 X1.4736 Y1.0092
N1274 X1.4866 Y0.9912
N1275 X1.4887 Y0.988
N1276 X1.5015 Y0.9668
N1277 X1.5078 Y0.9554
N1278 X1.5126 Y0.9456
N1279 X1.5221 Y0.9244
N1280 X1.529 Y0.9059
N1281 X1.5299 Y0.9032
N1282 X1.5366 Y0.882
N1283 X1.5417 Y0.8608
N1284 X1.5455 Y0.8396
N1285 X1.5483 Y0.8184
N1286 X1.5496 Y0.7972
N1287 X1.55 Y0.776
N1288 Y-0.5387
N1289 X1.5492 Y-0.5599
N1290 X1.5474 Y-0.5811
N1291 X1.5443 Y-0.6023
N1292 X1.5399 Y-0.6235
N1293 X1.5343 Y-0.6447
N1294 X1.529 Y-0.6609
N1295 X1.5272 Y-0.6659
N1296 X1.5188 Y-0.6871
N1297 X1.5088 Y-0.7083
N1298 X1.5078 Y-0.7103
N1299 X1.497 Y-0.7295
N1300 X1.4866 Y-0.7461
N1301 X1.4834 Y-0.7507
N1302 X1.4677 Y-0.7719
N1303 X1.4654 Y-0.7747
N1304 X1.4492 Y-0.7931
N1305 X1.4442 Y-0.7985
N1306 X1.4278 Y-0.8143
N1307 X1.423 Y-0.8186
N1308 X1.4049 Y-0.8355
N1309 X1.4018 Y-0.8518
N1310 X1.4007 Y-0.8567
N1311 X1.3954 Y-0.8779
N1312 X1.3887 Y-0.8991
N1313 X1.3807 Y-0.9203
N1314 X1.3711 Y-0.9415
N1315 X1.3593 Y-0.9638
N1316 X1.347 Y-0.9839
N1317 X1.3381 Y-0.9969
N1318 X1.3321 Y-1.0051
N1319 X1.3169 Y-1.0239
N1320 X1.3149 Y-1.0263
N1321 X1.2948 Y-1.0475
N1322 X1.2745 Y-1.066
N1323 X1.2713 Y-1.0688
N1324 X1.2533 Y-1.083
N1325 X1.2433 Y-1.09
N1326 X1.2321 Y-1.0975
N1327 X1.2109 Y-1.11
N1328 X1.2088 Y-1.1112
N1329 X1.1897 Y-1.121
N1330 X1.1685 Y-1.1302
N1331 X1.1631 Y-1.1324
N1332 X1.1473 Y-1.138
N1333 X1.1261 Y-1.1445
N1334 X1.1049 Y-1.1495
N1335 X1.0837 Y-1.1535
N1336 X1.0625 Y-1.1562
N1337 X1.0413 Y-1.1575
N1338 G00 Z-0.41
N1339 Z-0.31
N1340 Z0.2
N1341 X1.4647 Y-1.1575
N1342 Z0.14
N1343 Z0.04
N1344 G01 Z-0.31 F180.
N1345 X1.3139 Y-1.0256
N1346 X1.2957 Y-1.0429
N1347 X1.2745 Y-1.059
N1348 X1.2533 Y-1.0721
N1349 X1.2321 Y-1.0829
N1350 X1.2109 Y-1.0912
N1351 X1.1897 Y-1.0974
N1352 X1.1685 Y-1.1016
N1353 X1.1473 Y-1.104
N1354 X1.1261 Y-1.1047
N1355 X1.0201 Y-1.0988
N1356 X0.9353 Y-1.1043
N1357 X0.9141 Y-1.1035
N1358 X0.8929 Y-1.1011
N1359 X0.8717 Y-1.097
N1360 X0.8423 Y-1.09
N1361 X0.8293 Y-1.0857
N1362 X0.808 Y-1.0768
N1363 X0.7868 Y-1.0654
N1364 X0.7606 Y-1.0475
N1365 X0.7444 Y-1.034
N1366 X0.7367 Y-1.0263
N1367 X0.7356 Y-1.0251
N1368 X0.5848 Y-1.1573
N1369 G00 Z0.04
N1370 Z0.14
N1371 Z0.2
N1372 X-0.2204 Y1.357
N1373 Z-0.23
N1374 G01 Y1.1586 F180.
N1375 X-0.2069 Y1.1538
N1376 X-0.1803 Y1.1425
N1377 X-0.1544 Y1.1295
N1378 X-0.1295 Y1.1149
N1379 X-0.118 Y1.1071
N1380 X-0.0918 Y1.088
N1381 X-0.0814 Y1.0798
N1382 X-0.0715 Y1.071
N1383 X-0.0472 Y1.0477
N1384 X-0.0384 Y1.0388
N1385 X-0.0302 Y1.0294
N1386 X-0.0121 Y1.0071
N1387 X-0.004 Y0.9964
N1388 X0.012 Y0.9722
N1389 X0.0485 Y0.971
N1390 X0.0849 Y0.9683
N1391 X0.0871 Y0.968
N1392 X0.125 Y0.9632
N1393 X0.1626 Y0.9566
N1394 X0.1999 Y0.9484
N1395 X0.2135 Y0.9725
N1396 X0.2285 Y0.9957
N1397 X0.2308 Y0.9989
N1398 X0.2474 Y1.0206
N1399 X0.2652 Y1.0412
N1400 X0.2841 Y1.0608
N1401 X0.3042 Y1.0793
N1402 X0.3253 Y1.0966
N1403 X0.3286 Y1.0992
N1404 X0.3522 Y1.1154
N1405 X0.3767 Y1.1302
N1406 X0.402 Y1.1435
N1407 X0.4282 Y1.1551
N1408 X0.4376 Y1.1586
N1409 Y1.357
N1410 G00 Z0.12
N1411 X-0.8813
N1412 Z-0.23
N1413 G01 Y1.1567 F180.
N1414 X-0.867 Y1.1554
N1415 X-0.8458 Y1.1516
N1416 X-0.8246 Y1.1459
N1417 X-0.8034 Y1.1382
N1418 X-0.7822 Y1.1281
N1419 X-0.7608 Y1.1152
N1420 X-0.7335 Y1.094
N1421 X-0.7124 Y1.0728
N1422 X-0.6974 Y1.0541
N1423 X-0.6823 Y1.0304
N1424 X-0.6762 Y1.019
N1425 X-0.6619 Y0.9846
N1426 X-0.3582 Y0.9843
N1427 X-0.3369 Y0.9824
N1428 X-0.3157 Y0.9786
N1429 X-0.2945 Y0.9729
N1430 X-0.2733 Y0.9651
N1431 X-0.2521 Y0.955
N1432 X-0.236 Y0.9456
N1433 X-0.2097 Y0.9264
N1434 X-0.1854 Y0.9032
N1435 X-0.1673 Y0.8809
N1436 X-0.1542 Y0.8608
N1437 X-0.1461 Y0.8458
N1438 X-0.1345 Y0.8184
N1439 X-0.128 Y0.7972
N1440 X-0.1205 Y0.7619
N1441 X-0.0613 Y0.7697
N1442 X-0.0189 Y0.7722
N1443 X0.0023 Y0.7726
N1444 X0.0447 Y0.771
N1445 X0.0659 Y0.7692
N1446 X0.0871 Y0.7668
N1447 X0.1295 Y0.7594
N1448 X0.1719 Y0.7494
N1449 X0.2143 Y0.7362
N1450 X0.2356 Y0.7284
N1451 X0.2733 Y0.7124
N1452 X0.2992 Y0.6996
N1453 X0.3204 Y0.688
N1454 X0.3586 Y0.6651
N1455 X0.3524 Y0.6912
N1456 X0.3492 Y0.7124
N1457 X0.3479 Y0.7336
N1458 X0.3484 Y0.7548
N1459 X0.3506 Y0.776
N1460 X0.3548 Y0.7972
N1461 X0.3628 Y0.8237
N1462 X0.3692 Y0.8396
N1463 X0.3798 Y0.8608
N1464 X0.3931 Y0.882
N1465 X0.4052 Y0.8979
N1466 X0.4264 Y0.9205
N1467 X0.4476 Y0.9384
N1468 X0.4688 Y0.9527
N1469 X0.49 Y0.9641
N1470 X0.5112 Y0.9731
N1471 X0.5324 Y0.9798
N1472 X0.5536 Y0.9846
N1473 X0.5853 Y0.988
N1474 X0.5812
N1475 X0.6052 Y1.0304
N1476 X0.6172 Y1.0481
N1477 X0.6381 Y1.0728
N1478 X0.6596 Y1.0927
N1479 X0.6808 Y1.1082
N1480 X0.702 Y1.1206
N1481 X0.7232 Y1.1305
N1482 X0.7444 Y1.1381
N1483 X0.7656 Y1.1436
N1484 X0.7868 Y1.1473
N1485 X0.808 Y1.149
N1486 X0.9777 Y1.1494
N1487 X1.0201 Y1.1562
N1488 X1.0271 Y1.1566
N1489 Y1.357
N1490 G00 Z0.12
N1491 Z0.2
N1492 X0.2203 Y-1.1119
N1493 Z0.12
N1494 G01 Z-0.23 F180.
N1495 Y-0.9134
N1496 X0.2122 Y-0.9107
N1497 X0.185 Y-0.8994
N1498 X0.1585 Y-0.8864
N1499 X0.133 Y-0.8717
N1500 X0.1084 Y-0.8553
N1501 X0.085 Y-0.8374
N1502 X0.0628 Y-0.818
N1503 X0.0419 Y-0.7972
N1504 X0.0224 Y-0.7751
N1505 X0.0044 Y-0.7517
N1506 X-0.012 Y-0.7272
N1507 X-0.0232 Y-0.727
N1508 X-0.0256 Y-0.727
N1509 X-0.0608 Y-0.7251
N1510 X-0.0959 Y-0.7218
N1511 X-0.1309 Y-0.717
N1512 X-0.1656 Y-0.7109
N1513 X-0.2001 Y-0.7033
N1514 X-0.2121 Y-0.7248
N1515 X-0.2253 Y-0.7455
N1516 X-0.2395 Y-0.7655
N1517 X-0.2549 Y-0.7847
N1518 X-0.2712 Y-0.803
N1519 X-0.2809 Y-0.8126
N1520 X-0.3038 Y-0.8338
N1521 X-0.3141 Y-0.8428
N1522 X-0.325 Y-0.8509
N1523 X-0.3553 Y-0.8721
N1524 X-0.3644 Y-0.8781
N1525 X-0.3738 Y-0.8836
N1526 X-0.3892 Y-0.8921
N1527 X-0.3981 Y-0.8967
N1528 X-0.4072 Y-0.9008
N1529 X-0.4368 Y-0.9134
N1530 Y-1.1119
N1531 G00 Z0.12
N1532 X1.5259 Y-0.9923
N1533 Z-0.23
N1534 G01 X1.391 Y-0.8437 F180.
N1535 X1.3805 Y-0.8511
N1536 X1.3561 Y-0.8779
N1537 X1.3317 Y-0.8991
N1538 X1.3169 Y-0.9094
N1539 X1.2986 Y-0.9203
N1540 X1.2745 Y-0.9317
N1541 X1.2533 Y-0.9392
N1542 X1.2321 Y-0.9446
N1543 X1.2109 Y-0.9482
N1544 X1.1897 Y-0.95
N1545 X1.0625 Y-0.9501
N1546 X1.0201 Y-0.9472
N1547 X0.9989 Y-0.9496
N1548 X0.9777 Y-0.9502
N1549 X0.8929
N1550 X0.8717 Y-0.9485
N1551 X0.8505 Y-0.9453
N1552 X0.8293 Y-0.9399
N1553 X0.808 Y-0.9328
N1554 X0.7868 Y-0.9231
N1555 X0.7656 Y-0.911
N1556 X0.7444 Y-0.8959
N1557 X0.7232 Y-0.877
N1558 X0.702 Y-0.8531
N1559 X0.6898 Y-0.8355
N1560 X0.6808 Y-0.8205
N1561 X0.6679 Y-0.7931
N1562 X0.6605 Y-0.7719
N1563 X0.6521 Y-0.7395
N1564 X0.3628 Y-0.7394
N1565 X0.3416 Y-0.7378
N1566 X0.3204 Y-0.7345
N1567 X0.2992 Y-0.7292
N1568 X0.278 Y-0.7219
N1569 X0.2568 Y-0.7123
N1570 X0.2356 Y-0.7002
N1571 X0.2143 Y-0.6851
N1572 X0.1931 Y-0.6662
N1573 X0.174 Y-0.6447
N1574 X0.159 Y-0.6235
N1575 X0.1507 Y-0.6096
N1576 X0.1374 Y-0.5811
N1577 X0.1295 Y-0.5578
N1578 X0.1249 Y-0.5387
N1579 X0.1214 Y-0.5164
N1580 X0.0659 Y-0.524
N1581 X0.0235 Y-0.527
N1582 X0.0023 Y-0.5274
N1583 X-0.0189 Y-0.5271
N1584 X-0.0613 Y-0.5245
N1585 X-0.0825 Y-0.5222
N1586 X-0.1249 Y-0.5153
N1587 X-0.1461 Y-0.5108
N1588 X-0.1885 Y-0.4994
N1589 X-0.2097 Y-0.4927
N1590 X-0.2521 Y-0.4766
N1591 X-0.2945 Y-0.457
N1592 X-0.3369 Y-0.4332
N1593 X-0.3582 Y-0.4201
N1594 X-0.351 Y-0.4538
N1595 X-0.3485 Y-0.4751
N1596 X-0.3478 Y-0.4963
N1597 X-0.349 Y-0.5175
N1598 X-0.352 Y-0.5387
N1599 X-0.3582 Y-0.5645
N1600 X-0.3637 Y-0.5811
N1601 X-0.3728 Y-0.6023
N1602 X-0.3843 Y-0.6235
N1603 X-0.4006 Y-0.647
N1604 X-0.4168 Y-0.6659
N1605 X-0.4397 Y-0.6871
N1606 X-0.47 Y-0.7083
N1607 X-0.4854 Y-0.7167
N1608 X-0.5155 Y-0.7295
N1609 X-0.5278 Y-0.7334
N1610 X-0.549 Y-0.7386
N1611 X-0.5843 Y-0.7441
N1612 X-0.5974 Y-0.7719
N1613 X-0.6126 Y-0.7966
N1614 X-0.6261 Y-0.8143
N1615 X-0.646 Y-0.8355
N1616 X-0.655 Y-0.8437
N1617 X-0.6716 Y-0.8567
N1618 X-0.6974 Y-0.8731
N1619 X-0.7186 Y-0.8834
N1620 X-0.7398 Y-0.8917
N1621 X-0.7686 Y-0.8991
N1622 X-0.7822 Y-0.9015
N1623 X-0.8034 Y-0.9036
N1624 X-0.9731 Y-0.9042
N1625 X-0.9943 Y-0.9066
N1626 X-1.0155 Y-0.9103
N1627 X-1.0296 Y-0.9116
N1628 Y-1.1119
N1629 G00 Z0.12
N1630 Z0.2
N1631 X1.5138 Y-1.0011
N1632 Z0.13
N1633 G01 Z-0.22 F180.
N1634 X1.3672 Y-0.8643
N1635 X1.3535 Y-0.8779
N1636 X1.3381 Y-0.891
N1637 X1.3169 Y-0.9056
N1638 X1.2957 Y-0.9174
N1639 X1.2745 Y-0.9266
N1640 X1.2533 Y-0.9336
N1641 X1.2321 Y-0.9388
N1642 X1.2109 Y-0.9417
N1643 X1.1897 Y-0.9431
N1644 X1.0625 Y-0.9434
N1645 X1.0201 Y-0.9421
N1646 X0.9989 Y-0.9433
N1647 X0.8929
N1648 X0.8717 Y-0.9418
N1649 X0.8505 Y-0.9387
N1650 X0.8293 Y-0.9332
N1651 X0.808 Y-0.9259
N1652 X0.7868 Y-0.9163
N1653 X0.7579 Y-0.8991
N1654 X0.7444 Y-0.8892
N1655 X0.7313 Y-0.8779
N1656 X0.7107 Y-0.8567
N1657 X0.702 Y-0.8461
N1658 X0.6942 Y-0.8355
N1659 X0.6812 Y-0.8143
N1660 X0.6707 Y-0.7931
N1661 X0.6627 Y-0.7719
N1662 X0.6535 Y-0.7395
N1663 X0.6514
N1664 X0.52 Y-0.9389
N1665 G00 Z0.13
N1666 Z0.2
N1667 X0.2329 Y1.35
N1668 Z-0.0824
N1669 Z-0.1824
N1670 G01 X-0.106 Y-0.0469 Z-0.22 F180.
N1671 X-0.0921 Y-0.0323
N1672 X-0.0855 Y-0.0258
N1673 X-0.053 Y0.0068
N1674 X-0.0217 Y0.0405
N1675 X-0.0015 Y0.0642
N1676 X0.0182 Y0.0882
N1677 X0.064 Y0.1492
N1678 X0.0766 Y0.1652
N1679 X0.09 Y0.1804
N1680 X0.1112 Y0.2034
N1681 X0.1221 Y0.2148
N1682 X0.1335 Y0.2258
N1683 X0.1331 Y0.2367
N1684 X0.106 Y0.2919
N1685 X0.0975 Y0.283
N1686 X0.041 Y0.2257
N1687 X0.0149 Y0.1968
N1688 X-0.0203 Y0.154
N1689 X-0.047 Y0.1181
N1690 X-0.0745 Y0.0827
N1691 X-0.0888 Y0.0656
N1692 X-0.1106 Y0.042
N1693 X-0.1336 Y0.0195
N1694 X-0.1333 Y0.0091
N1695 X-0.1199 Y-0.0191
N1696 X-0.106 Y-0.0469
N1697 G00 Z0.13
N1698 Z0.2
N1699 X-0.1053 Y-0.7203
N1700 Z0.13
N1701 G01 Z-0.22 F180.
N1702 X-0.0783 Y-0.5237
N1703 X-0.0789 Y-0.5171
N1704 X-0.0798 Y-0.4889
N1705 X-0.0791 Y-0.4635
N1706 X-0.077 Y-0.4382
N1707 X-0.0734 Y-0.413
N1708 X-0.0684 Y-0.3881
N1709 X-0.0669 Y-0.3816
N1710 X-0.0606 Y-0.3596
N1711 X-0.0534 Y-0.3378
N1712 X-0.0453 Y-0.3163
N1713 X-0.0424 Y-0.3094
N1714 X-0.0304 Y-0.2844
N1715 X-0.017 Y-0.2601
N1716 X-0.0021 Y-0.2367
N1717 X0.0141 Y-0.2143
N1718 X0.0317 Y-0.1929
N1719 X0.0505 Y-0.1725
N1720 X0.0538 Y-0.1693
N1721 X0.0916 Y-0.1313
N1722 X0.1281 Y-0.092
N1723 X0.1525 Y-0.0635
N1724 X0.1762 Y-0.0345
N1725 X0.224 Y0.0292
N1726 X0.2303 Y0.0372
N1727 X0.237 Y0.0448
N1728 X0.2582 Y0.0678
N1729 X0.2664 Y0.0763
N1730 X0.2752 Y0.0842
N1731 X0.2964 Y0.1023
N1732 X0.3064 Y0.1103
N1733 X0.3207 Y0.1206
N1734 X0.3354 Y0.1304
N1735 X0.3342 Y0.208
N1736 X0.3311 Y0.2856
N1737 X0.3294 Y0.2892
N1738 X0.3016 Y0.3477
N1739 X0.2725 Y0.4056
N1740 X0.2444 Y0.4542
N1741 X0.215 Y0.5021
N1742 X0.2126 Y0.506
N1743 X0.1993 Y0.5296
N1744 X0.1875 Y0.5541
N1745 X0.1771 Y0.5791
N1746 X0.1683 Y0.6048
N1747 X0.1611 Y0.631
N1748 X0.1554 Y0.6575
N1749 X0.1513 Y0.6843
N1750 X0.1489 Y0.7114
N1751 X0.148 Y0.7385
N1752 X0.1486 Y0.7563
N1753 X0.1944 Y0.9491
N1754 G00 Z0.13
N1755 X-0.0109 Y-0.7267
N1756 Z-0.22
N1757 G01 X0.1216 Y-0.5173 F180.
N1758 X0.1201 Y-0.4963
N1759 X0.1204 Y-0.4751
N1760 X0.1225 Y-0.4538
N1761 X0.1265 Y-0.4326
N1762 X0.1295 Y-0.421
N1763 X0.1405 Y-0.3902
N1764 X0.1509 Y-0.369
N1765 X0.164 Y-0.3478
N1766 X0.1803 Y-0.3266
N1767 X0.1931 Y-0.3127
N1768 X0.2427 Y-0.263
N1769 X0.278 Y-0.2245
N1770 X0.2992 Y-0.2
N1771 X0.3343 Y-0.157
N1772 X0.384 Y-0.0908
N1773 X0.4052 Y-0.0678
N1774 X0.4264 Y-0.0497
N1775 X0.4476 Y-0.0351
N1776 X0.4688 Y-0.0235
N1777 X0.49 Y-0.0144
N1778 X0.5076 Y-0.0086
N1779 X0.5324 Y-0.0026
N1780 X0.5344 Y0.0338
N1781 X0.5355 Y0.1187
N1782 X0.5345 Y0.2035
N1783 X0.5314 Y0.2883
N1784 X0.5289 Y0.3307
N1785 X0.524 Y0.3519
N1786 X0.5109 Y0.3731
N1787 X0.4705 Y0.4579
N1788 X0.4487 Y0.5003
N1789 X0.4247 Y0.5427
N1790 X0.384 Y0.6091
N1791 X0.3738 Y0.6275
N1792 X0.3645 Y0.6487
N1793 X0.3585 Y0.6669
N1794 X0.2011 Y0.9475
N1795 G00 Z0.13
N1796 Z0.2
N1797 X0.1007 Y0.966
N1798 Z0.13
N1799 G01 Z-0.22 F180.
N1800 X0.0784 Y0.7691
N1801 X0.0789 Y0.7637
N1802 X0.0799 Y0.734
N1803 X0.0791 Y0.7083
N1804 X0.0769 Y0.6827
N1805 X0.0733 Y0.6573
N1806 X0.0727 Y0.6537
N1807 X0.0674 Y0.6296
N1808 X0.0609 Y0.6058
N1809 X0.0532 Y0.5823
N1810 X0.0443 Y0.5593
N1811 X0.0342 Y0.5368
N1812 X0.0318 Y0.5319
N1813 X0.0198 Y0.51
N1814 X0.0066 Y0.4887
N1815 X-0.0077 Y0.4681
N1816 X-0.023 Y0.4483
N1817 X-0.0393 Y0.4293
N1818 X-0.0449 Y0.4235
N1819 X-0.1045 Y0.363
N1820 X-0.1367 Y0.3274
N1821 X-0.1785 Y0.2764
N1822 X-0.2046 Y0.2413
N1823 X-0.2314 Y0.2067
N1824 X-0.2385 Y0.1981
N1825 X-0.257 Y0.1784
N1826 X-0.2766 Y0.1597
N1827 X-0.2971 Y0.1422
N1828 X-0.3187 Y0.1258
N1829 X-0.3325 Y0.1167
N1830 X-0.3353 Y0.1151
N1831 X-0.3342 Y0.0378
N1832 X-0.3315 Y-0.0394
N1833 X-0.3298 Y-0.0427
N1834 X-0.3242 Y-0.0542
N1835 X-0.3067 Y-0.0922
N1836 X-0.2882 Y-0.1298
N1837 X-0.2688 Y-0.167
N1838 X-0.2413 Y-0.2146
N1839 X-0.2124 Y-0.2614
N1840 X-0.2063 Y-0.2717
N1841 X-0.1941 Y-0.295
N1842 X-0.1832 Y-0.319
N1843 X-0.1736 Y-0.3435
N1844 X-0.171 Y-0.3512
N1845 X-0.1618 Y-0.3836
N1846 X-0.1545 Y-0.4165
N1847 X-0.1534 Y-0.423
N1848 X-0.1504 Y-0.4462
N1849 X-0.1486 Y-0.4695
N1850 X-0.148 Y-0.4929
N1851 X-0.1485 Y-0.5113
N1852 X-0.1947 Y-0.7041
N1853 G00 Z0.13
N1854 X0.0112 Y0.9718
N1855 Z-0.22
N1856 G01 X-0.1223 Y0.7664 F180.
N1857 X-0.1208 Y0.7548
N1858 X-0.12 Y0.7336
N1859 X-0.121 Y0.7124
N1860 X-0.1238 Y0.6912
N1861 X-0.1285 Y0.6699
N1862 X-0.1352 Y0.6487
N1863 X-0.1461 Y0.6233
N1864 X-0.1554 Y0.6063
N1865 X-0.1696 Y0.5851
N1866 X-0.1873 Y0.5639
N1867 X-0.25 Y0.5003
N1868 X-0.2883 Y0.4579
N1869 X-0.3369 Y0.3987
N1870 X-0.3794 Y0.3417
N1871 X-0.3883 Y0.3307
N1872 X-0.4006 Y0.3174
N1873 X-0.4218 Y0.2984
N1874 X-0.4353 Y0.2883
N1875 X-0.4642 Y0.271
N1876 X-0.4854 Y0.2613
N1877 X-0.5066 Y0.254
N1878 X-0.5331 Y0.2473
N1879 X-0.5346 Y0.2035
N1880 X-0.5355 Y0.1399
N1881 X-0.5348 Y0.055
N1882 X-0.5312 Y-0.051
N1883 X-0.5278 Y-0.1014
N1884 X-0.5188 Y-0.1146
N1885 X-0.5068 Y-0.1358
N1886 X-0.4772 Y-0.1994
N1887 X-0.4443 Y-0.263
N1888 X-0.4203 Y-0.3054
N1889 X-0.381 Y-0.369
N1890 X-0.3701 Y-0.3902
N1891 X-0.3617 Y-0.4114
N1892 X-0.3583 Y-0.4218
N1893 X-0.201 Y-0.7026
N1894 G00 Z0.13
N1895 Z0.2
N1896 X-0.4557 Y-0.9194
N1897 Z0.13
N1898 G01 Z-0.22 F180.
N1899 X-0.5795 Y-0.7426
N1900 X-0.6081 Y-0.7445
N1901 X-0.6239 Y-0.7719
N1902 X-0.639 Y-0.7931
N1903 X-0.6579 Y-0.8143
N1904 X-0.6762 Y-0.8308
N1905 X-0.6974 Y-0.8464
N1906 X-0.7186 Y-0.8589
N1907 X-0.7398 Y-0.8687
N1908 X-0.761 Y-0.8764
N1909 X-0.7822 Y-0.8818
N1910 X-0.8034 Y-0.8854
N1911 X-0.8246 Y-0.8871
N1912 X-0.9307 Y-0.8875
N1913 X-0.9519 Y-0.8932
N1914 X-0.9731 Y-0.9009
N1915 X-0.9892 Y-0.9052
N1916 X-0.9657 Y-1.1041
N1917 G00 Z0.13
N1918 Z0.2
N1919 X0.4561 Y1.164
N1920 Z0.13
N1921 G01 Z-0.22 F180.
N1922 X0.5843 Y0.988
N1923 X0.6062 Y0.9891
N1924 X0.6331 Y1.0304
N1925 X0.6384 Y1.0374
N1926 X0.6505 Y1.0516
N1927 X0.6725 Y1.0728
N1928 X0.6808 Y1.0796
N1929 X0.702 Y1.0946
N1930 X0.7232 Y1.1063
N1931 X0.743 Y1.1152
N1932 X0.7656 Y1.1228
N1933 X0.7868 Y1.1278
N1934 X0.808 Y1.1311
N1935 X0.8293 Y1.1324
N1936 X0.9353 Y1.1326
N1937 X0.9565 Y1.1409
N1938 X0.9777 Y1.148
N1939 X0.9835 Y1.1494
N1940 X0.9616 Y1.3488
N1941 G00 Z0.13
N1942 Z0.22
N1943 X1.5095 Y-1.0042
N1944 G01 Z-0.13 F180.
N1945 X1.3781 Y-0.8527
N1946 X1.3593 Y-0.8647
N1947 X1.3346 Y-0.8779
N1948 X1.3169 Y-0.8856
N1949 X1.2745 Y-0.9
N1950 X1.2321 Y-0.9087
N1951 X1.2109 Y-0.9113
N1952 X1.1685 Y-0.9133
N1953 X0.8929 Y-0.9131
N1954 X0.8717 Y-0.9118
N1955 X0.8505 Y-0.9082
N1956 X0.8293 Y-0.903
N1957 X0.808 Y-0.8959
N1958 X0.7868 Y-0.8861
N1959 X0.7656 Y-0.8741
N1960 X0.7444 Y-0.859
N1961 X0.7232 Y-0.8402
N1962 X0.702 Y-0.8159
N1963 X0.6863 Y-0.7931
N1964 X0.6749 Y-0.7719
N1965 X0.6609 Y-0.7394
N1966 X0.6524
N1967 X0.5242 Y-0.9389
N1968 G00 Z0.22
N1969 X0.3359 Y0.1297
N1970 G01 Z-0.13 F180.
N1971 X0.5318 Y-0.0028
N1972 X0.5324 Y-0.0026
N1973 X0.5536 Y0.0004
N1974 X0.5748 Y0.0016
N1975 X0.8361
N1976 X0.8551 Y0.0338
N1977 X0.8706 Y0.055
N1978 X0.8902 Y0.0762
N1979 X0.9152 Y0.0974
N1980 X0.9353 Y0.1109
N1981 X0.9735 Y0.1314
N1982 X0.9746 Y0.1823
N1983 X0.9743 Y0.2435
N1984 X0.7232 Y0.2436
N1985 X0.702 Y0.2451
N1986 X0.6808 Y0.2484
N1987 X0.6596 Y0.2537
N1988 X0.6384 Y0.2609
N1989 X0.6172 Y0.2704
N1990 X0.596 Y0.2825
N1991 X0.5873 Y0.2883
N1992 X0.5748 Y0.2975
N1993 X0.5536 Y0.3164
N1994 X0.5324 Y0.3404
N1995 X0.5242 Y0.3516
N1996 X0.3317 Y0.2863
N1997 G00 Z0.22
N1998 X0.4944 Y1.1755
N1999 G01 Z-0.13 F180.
N2000 X0.6048 Y0.9886
N2001 X0.808
N2002 X0.8285 Y1.0304
N2003 X0.842 Y1.0516
N2004 X0.8587 Y1.0728
N2005 X0.8797 Y1.094
N2006 X0.8929 Y1.105
N2007 X0.9071 Y1.1152
N2008 X0.9353 Y1.1316
N2009 X0.9372 Y1.1324
N2010 X0.8991 Y1.332
N2011 G00 Z0.22
N2012 X-0.3358 Y0.1157
N2013 G01 Z-0.13 F180.
N2014 X-0.5322 Y0.2479
N2015 X-0.549 Y0.2452
N2016 X-0.5702 Y0.2437
N2017 X-0.835 Y0.2436
N2018 X-0.8604 Y0.2035
N2019 X-0.867 Y0.1946
N2020 X-0.8773 Y0.1823
N2021 X-0.8986 Y0.1611
N2022 X-0.9094 Y0.1521
N2023 X-0.9307 Y0.1371
N2024 X-0.9519 Y0.1251
N2025 X-0.9731 Y0.1157
N2026 X-0.9746 Y0.055
N2027 X-0.9741 Y0.0016
N2028 X-0.7186 Y0.0013
N2029 X-0.6974 Y-0.0006
N2030 X-0.6762 Y-0.0043
N2031 X-0.655 Y-0.01
N2032 X-0.6338 Y-0.0177
N2033 X-0.6126 Y-0.0277
N2034 X-0.5914 Y-0.0404
N2035 X-0.5702 Y-0.0562
N2036 X-0.5527 Y-0.0722
N2037 X-0.5339 Y-0.0934
N2038 X-0.5276 Y-0.1022
N2039 X-0.332 Y-0.0405
N2040 G00 Z0.22
N2041 X-0.4943 Y-0.9304
N2042 G01 Z-0.13 F180.
N2043 X-0.6034 Y-0.7434
N2044 X-0.811 Y-0.7434
N2045 X-0.8246 Y-0.7745
N2046 X-0.835 Y-0.7931
N2047 X-0.8495 Y-0.8143
N2048 X-0.867 Y-0.8348
N2049 X-0.8882 Y-0.8546
N2050 X-0.9094 Y-0.8705
N2051 X-0.9307 Y-0.8831
N2052 X-0.9483 Y-0.8914
N2053 X-0.9012 Y-1.0869
N2054 G00 Z0.22
N2055 Z0.32
N2056 X-0.1603 Y1.1307
N2057 G01 Z-0.03 F180.
N2058 X-0.2521 Y0.9545
N2059 X-0.2511 Y0.9407
N2060 X-0.2502 Y0.9075
N2061 X-0.2511 Y0.8743
N2062 X-0.2536 Y0.8412
N2063 X-0.2578 Y0.8083
N2064 X-0.2637 Y0.7757
N2065 X-0.2712 Y0.7434
N2066 X-0.2804 Y0.7115
N2067 X-0.2912 Y0.6801
N2068 X-0.3036 Y0.6493
N2069 X-0.3175 Y0.6192
N2070 X-0.3206 Y0.613
N2071 X-0.3357 Y0.5853
N2072 X-0.352 Y0.5584
N2073 X-0.3696 Y0.5322
N2074 X-0.3885 Y0.5069
N2075 X-0.4084 Y0.4825
N2076 X-0.4295 Y0.4591
N2077 X-0.4402 Y0.4481
N2078 X-0.4514 Y0.4376
N2079 X-0.4747 Y0.4164
N2080 X-0.4865 Y0.4061
N2081 X-0.4987 Y0.3963
N2082 X-0.5276 Y0.375
N2083 X-0.5575 Y0.3553
N2084 X-0.5885 Y0.3371
N2085 X-0.601 Y0.3305
N2086 X-0.8905 Y0.1833
N2087 X-0.8827 Y0.1766
N2088 X-0.4176 Y0.0742
N2089 X-0.7362 Y0.0018
N2090 X-0.6981 Y-0.0609
N2091 X-0.6751 Y-0.0946
N2092 X-0.651 Y-0.1275
N2093 X-0.6256 Y-0.1595
N2094 X-0.5991 Y-0.1905
N2095 X-0.5715 Y-0.2206
N2096 X-0.5583 Y-0.2352
N2097 X-0.5387 Y-0.259
N2098 X-0.5203 Y-0.2835
N2099 X-0.5029 Y-0.3089
N2100 X-0.4867 Y-0.335
N2101 X-0.4828 Y-0.3417
N2102 X-0.467 Y-0.3712
N2103 X-0.4528 Y-0.4016
N2104 X-0.4402 Y-0.4327
N2105 X-0.4292 Y-0.4643
N2106 X-0.4198 Y-0.4965
N2107 X-0.4121 Y-0.5292
N2108 X-0.4061 Y-0.5622
N2109 X-0.4018 Y-0.5954
N2110 X-0.3992 Y-0.6288
N2111 X-0.3988 Y-0.6442
N2112 X-0.2422 Y-0.7665
N2113 G00 Z0.32
N2114 X0.1547 Y-0.8829
N2115 G01 Z-0.03 F180.
N2116 X0.2522 Y-0.7096
N2117 X0.2512 Y-0.6979
N2118 X0.2502 Y-0.6623
N2119 X0.2511 Y-0.6282
N2120 X0.2538 Y-0.5942
N2121 X0.2583 Y-0.5603
N2122 X0.2645 Y-0.5267
N2123 X0.2724 Y-0.4936
N2124 X0.2821 Y-0.4608
N2125 X0.2935 Y-0.4287
N2126 X0.3066 Y-0.3971
N2127 X0.3105 Y-0.3887
N2128 X0.3273 Y-0.3555
N2129 X0.3458 Y-0.3233
N2130 X0.3659 Y-0.292
N2131 X0.3745 Y-0.2798
N2132 X0.3836 Y-0.268
N2133 X0.4006 Y-0.2468
N2134 X0.4152 Y-0.2295
N2135 X0.4308 Y-0.213
N2136 X0.4521 Y-0.1918
N2137 X0.4639 Y-0.1805
N2138 X0.4762 Y-0.1696
N2139 X0.498 Y-0.1519
N2140 X0.5205 Y-0.1349
N2141 X0.5436 Y-0.1189
N2142 X0.564 Y-0.1061
N2143 X0.7508 Y0.0029
N2144 X0.4178 Y0.1709
N2145 G00 Z0.32
N2146 X0.457 Y-0.9389
N2147 Z-0.03
N2148 G01 X0.4571 Y-0.7403 F180.
N2149 X0.4535 Y-0.717
N2150 X0.4511 Y-0.6897
N2151 X0.4502 Y-0.6623
N2152 X0.451 Y-0.6353
N2153 X0.4535 Y-0.6083
N2154 X0.4575 Y-0.5816
N2155 X0.4631 Y-0.5552
N2156 X0.4703 Y-0.5291
N2157 X0.4791 Y-0.5035
N2158 X0.4893 Y-0.4785
N2159 X0.4913 Y-0.4743
N2160 X0.5033 Y-0.4504
N2161 X0.5166 Y-0.4272
N2162 X0.5311 Y-0.4047
N2163 X0.54 Y-0.3927
N2164 X0.5569 Y-0.3715
N2165 X0.5642 Y-0.3629
N2166 X0.572 Y-0.3546
N2167 X0.5933 Y-0.3334
N2168 X0.6054 Y-0.3223
N2169 X0.6295 Y-0.3031
N2170 X0.6546 Y-0.2852
N2171 X0.6648 Y-0.2789
N2172 X1.0465 Y-0.0561
N2173 X1.0542 Y-0.0519
N2174 X1.0795 Y-0.0395
N2175 X1.1055 Y-0.0288
N2176 X1.1322 Y-0.0196
N2177 X1.1593 Y-0.0122
N2178 X1.1869 Y-0.0064
N2179 X1.2148 Y-0.0023
N2180 X1.2428 Y0.
N2181 X1.252 Y0.0003
N2182 X1.294 Y0.0006
N2183 X1.2986
N2184 X1.3252 Y-0.0002
N2185 X1.3518 Y-0.0025
N2186 X1.3782 Y-0.0064
N2187 X1.4044 Y-0.0118
N2188 X1.4302 Y-0.0188
N2189 X1.4555 Y-0.0272
N2190 X1.4803 Y-0.0371
N2191 X1.4835 Y-0.0386
N2192 X1.5075 Y-0.0503
N2193 X1.5308 Y-0.0634
N2194 X1.5513 Y-0.0765
N2195 X1.7495
N2196 G00 Z0.32
N2197 X0.5457 Y-0.9389
N2198 Z-0.03
N2199 G01 X0.664 Y-0.7444 F180.
N2200 X0.6596 Y-0.7312
N2201 X0.6542 Y-0.7083
N2202 X0.6512 Y-0.6871
N2203 X0.65 Y-0.6659
N2204 X0.6506 Y-0.6447
N2205 X0.653 Y-0.6235
N2206 X0.6573 Y-0.6023
N2207 X0.6636 Y-0.5811
N2208 X0.672 Y-0.5599
N2209 X0.6808 Y-0.5422
N2210 X0.6963 Y-0.5175
N2211 X0.7132 Y-0.4963
N2212 X0.7345 Y-0.4751
N2213 X0.7444 Y-0.4667
N2214 X0.7656 Y-0.4516
N2215 X1.1473 Y-0.2289
N2216 X1.1685 Y-0.2188
N2217 X1.1897 Y-0.211
N2218 X1.2109 Y-0.2053
N2219 X1.2321 Y-0.2016
N2220 X1.2533 Y-0.1997
N2221 X1.2957 Y-0.1994
N2222 X1.3169 Y-0.2
N2223 X1.3381 Y-0.2024
N2224 X1.3593 Y-0.2066
N2225 X1.3805 Y-0.2128
N2226 X1.4007 Y-0.2206
N2227 X1.423 Y-0.2318
N2228 X1.4442 Y-0.2452
N2229 X1.4654 Y-0.2619
N2230 X1.4866 Y-0.283
N2231 X1.5044 Y-0.3054
N2232 X1.5178 Y-0.3266
N2233 X1.529 Y-0.3491
N2234 X1.5367 Y-0.369
N2235 X1.5429 Y-0.3902
N2236 X1.5471 Y-0.4114
N2237 X1.5491 Y-0.4298
N2238 X1.7495
N2239 G00 Z0.32
N2240 X0.4178 Y0.1709
N2241 G01 Z-0.03 F180.
N2242 X0.7363 Y0.2428
N2243 X0.7181 Y0.2733
N2244 X0.6954 Y0.3085
N2245 X0.6714 Y0.3429
N2246 X0.6463 Y0.3765
N2247 X0.62 Y0.4091
N2248 X0.5487 Y0.4898
N2249 X0.5336 Y0.508
N2250 X0.5195 Y0.5271
N2251 X0.5048 Y0.5483
N2252 X0.4929 Y0.5665
N2253 X0.475 Y0.5976
N2254 X0.4588 Y0.6297
N2255 X0.4444 Y0.6625
N2256 X0.4318 Y0.6961
N2257 X0.4211 Y0.7304
N2258 X0.4123 Y0.7652
N2259 X0.4054 Y0.8004
N2260 X0.4004 Y0.8359
N2261 X0.3975 Y0.8717
N2262 X0.3971 Y0.887
N2263 X0.2376 Y1.0055
N2264 G00 Z0.32
N2265 X1.7495 Y0.1933
N2266 Z-0.03
N2267 G01 X1.5511 F180.
N2268 X1.5504 Y0.1928
N2269 X1.5254 Y0.1772
N2270 X1.4994 Y0.1633
N2271 X1.4725 Y0.1511
N2272 X1.4448 Y0.1407
N2273 X1.4166 Y0.1321
N2274 X1.3878 Y0.1254
N2275 X1.3587 Y0.1206
N2276 X1.3293 Y0.1177
N2277 X1.2998 Y0.1168
N2278 X1.2706 Y0.1177
N2279 X1.2415 Y0.1206
N2280 X1.2126 Y0.1253
N2281 X1.1841 Y0.1319
N2282 X1.1561 Y0.1403
N2283 X1.1287 Y0.1505
N2284 X1.102 Y0.1625
N2285 X1.0991 Y0.1639
N2286 X1.0754 Y0.1769
N2287 X1.0524 Y0.1911
N2288 X1.0303 Y0.2067
N2289 X1.0091 Y0.2235
N2290 X0.9889 Y0.2414
N2291 X0.9782 Y0.2523
N2292 X0.957 Y0.2756
N2293 X0.9487 Y0.2853
N2294 X0.9411 Y0.2956
N2295 X0.9225 Y0.322
N2296 X0.913 Y0.337
N2297 X0.8876 Y0.3794
N2298 X0.8608 Y0.4209
N2299 X0.8325 Y0.4615
N2300 X0.8028 Y0.501
N2301 X0.7718 Y0.5395
N2302 X0.6985 Y0.6223
N2303 X0.691 Y0.6314
N2304 X0.684 Y0.6409
N2305 X0.6693 Y0.6621
N2306 X0.6633 Y0.6713
N2307 X0.6496 Y0.6952
N2308 X0.6373 Y0.72
N2309 X0.6266 Y0.7455
N2310 X0.6175 Y0.7716
N2311 X0.61 Y0.7981
N2312 X0.6041 Y0.8251
N2313 X0.5999 Y0.8524
N2314 X0.5973 Y0.88
N2315 X0.5965 Y0.9076
N2316 X0.5974 Y0.9364
N2317 X0.6002 Y0.965
N2318 X0.604 Y0.9891
N2319 Y1.1881
N2320 G00 Z0.32
N2321 X1.7495 Y0.5461
N2322 Z-0.03
N2323 G01 X1.5491 F180.
N2324 X1.5489 Y0.5427
N2325 X1.5459 Y0.5215
N2326 X1.5411 Y0.5003
N2327 X1.5342 Y0.4791
N2328 X1.529 Y0.4662
N2329 X1.5136 Y0.4367
N2330 X1.4992 Y0.4155
N2331 X1.4866 Y0.4002
N2332 X1.4654 Y0.3791
N2333 X1.4583 Y0.3731
N2334 X1.4442 Y0.3623
N2335 X1.423 Y0.3489
N2336 X1.4018 Y0.3382
N2337 X1.3805 Y0.3299
N2338 X1.3593 Y0.3237
N2339 X1.3381 Y0.3195
N2340 X1.3169 Y0.3172
N2341 X1.2957 Y0.3166
N2342 X1.2745 Y0.3179
N2343 X1.2533 Y0.321
N2344 X1.2321 Y0.326
N2345 X1.2109 Y0.333
N2346 X1.1897 Y0.3422
N2347 X1.1719 Y0.3519
N2348 X1.1473 Y0.3686
N2349 X1.1261 Y0.387
N2350 X1.1049 Y0.4103
N2351 X1.0864 Y0.4367
N2352 X1.0611 Y0.4791
N2353 X1.0342 Y0.5215
N2354 X1.0052 Y0.5639
N2355 X0.9777 Y0.6017
N2356 X0.9565 Y0.6293
N2357 X0.9234 Y0.6699
N2358 X0.8484 Y0.7548
N2359 X0.8337 Y0.776
N2360 X0.8219 Y0.7972
N2361 X0.8127 Y0.8184
N2362 X0.8057 Y0.8396
N2363 X0.8007 Y0.8608
N2364 X0.7976 Y0.882
N2365 X0.7963 Y0.9032
N2366 X0.7968 Y0.9244
N2367 X0.7992 Y0.9456
N2368 X0.8034 Y0.9668
N2369 X0.8096 Y0.988
N2370 X0.8127 Y0.996
N2371 X0.6959 Y1.1881
N2372 G00 Z0.32
N2373 X-0.457 Y1.1839
N2374 G01 Z-0.03 F180.
N2375 X-0.4571 Y0.9851
N2376 X-0.4539 Y0.9649
N2377 X-0.4511 Y0.9363
N2378 X-0.4502 Y0.9075
N2379 X-0.4512 Y0.8779
N2380 X-0.4541 Y0.8485
N2381 X-0.4589 Y0.8193
N2382 X-0.4656 Y0.7905
N2383 X-0.4742 Y0.7622
N2384 X-0.4846 Y0.7346
N2385 X-0.4968 Y0.7076
N2386 X-0.4984 Y0.7046
N2387 X-0.5112 Y0.6813
N2388 X-0.5254 Y0.6587
N2389 X-0.5407 Y0.637
N2390 X-0.5573 Y0.6162
N2391 X-0.575 Y0.5963
N2392 X-0.5859 Y0.5856
N2393 X-0.6092 Y0.5644
N2394 X-0.6212 Y0.5543
N2395 X-0.6419 Y0.5391
N2396 X-0.6633 Y0.525
N2397 X-0.6853 Y0.5121
N2398 X-0.6916 Y0.5087
N2399 X-1.0942 Y0.3041
N2400 X-1.1183 Y0.2926
N2401 X-1.143 Y0.2826
N2402 X-1.1684 Y0.2741
N2403 X-1.1941 Y0.2671
N2404 X-1.2203 Y0.2616
N2405 X-1.2467 Y0.2576
N2406 X-1.2733 Y0.2553
N2407 X-1.3 Y0.2545
N2408 X-1.3276 Y0.2553
N2409 X-1.3551 Y0.2579
N2410 X-1.3825 Y0.2621
N2411 X-1.4095 Y0.268
N2412 X-1.4361 Y0.2755
N2413 X-1.4622 Y0.2846
N2414 X-1.4876 Y0.2953
N2415 X-1.5124 Y0.3076
N2416 X-1.5237 Y0.3141
N2417 X-1.5499 Y0.3303
N2418 X-1.5504 Y0.3306
N2419 X-1.7492 Y0.3307
N2420 G00 Z0.32
N2421 X-0.5462 Y1.184
N2422 Z-0.03
N2423 G01 X-0.6626 Y0.9856 F180.
N2424 X-0.6571 Y0.9668
N2425 X-0.6529 Y0.9456
N2426 X-0.6506 Y0.9244
N2427 X-0.65 Y0.9032
N2428 X-0.6513 Y0.882
N2429 X-0.6544 Y0.8608
N2430 X-0.6594 Y0.8396
N2431 X-0.6664 Y0.8184
N2432 X-0.6762 Y0.7961
N2433 X-0.6874 Y0.776
N2434 X-0.7021 Y0.7548
N2435 X-0.7205 Y0.7336
N2436 X-0.7438 Y0.7124
N2437 X-0.761 Y0.6997
N2438 X-0.7822 Y0.687
N2439 X-1.1851 Y0.4822
N2440 X-1.2063 Y0.4725
N2441 X-1.2275 Y0.465
N2442 X-1.2487 Y0.4596
N2443 X-1.2699 Y0.4561
N2444 X-1.2911 Y0.4544
N2445 X-1.3123 Y0.4546
N2446 X-1.3335 Y0.4565
N2447 X-1.3547 Y0.4604
N2448 X-1.3759 Y0.4661
N2449 X-1.3971 Y0.4739
N2450 X-1.4183 Y0.4841
N2451 X-1.4445 Y0.5003
N2452 X-1.4607 Y0.5128
N2453 X-1.4819 Y0.5328
N2454 X-1.4908 Y0.5427
N2455 X-1.5069 Y0.5639
N2456 X-1.5244 Y0.594
N2457 X-1.53 Y0.6063
N2458 X-1.5379 Y0.6275
N2459 X-1.5438 Y0.6487
N2460 X-1.5476 Y0.6699
N2461 X-1.5487 Y0.6815
N2462 X-1.7491 Y0.6816
N2463 G00 Z0.32
N2464 X-1.7493 Y0.0524
N2465 G01 Z-0.03 F180.
N2466 X-1.5506 Y0.0523
N2467 X-1.5502 Y0.0526
N2468 X-1.5274 Y0.0668
N2469 X-1.5038 Y0.0796
N2470 X-1.4794 Y0.091
N2471 X-1.4545 Y0.101
N2472 X-1.429 Y0.1095
N2473 X-1.403 Y0.1164
N2474 X-1.3767 Y0.1218
N2475 X-1.3501 Y0.1257
N2476 X-1.3233 Y0.1279
N2477 X-1.3123 Y0.1283
N2478 X-1.3096
N2479 X-1.2779 Y0.1278
N2480 X-1.2651 Y0.1272
N2481 X-1.2524 Y0.1258
N2482 X-1.2205 Y0.1213
N2483 X-1.206 Y0.1187
N2484 X-1.1774 Y0.1115
N2485 X-1.1493 Y0.1025
N2486 X-1.1218 Y0.0917
N2487 X-1.095 Y0.0792
N2488 X-1.0829 Y0.0726
N2489 X-1.0572 Y0.0573
N2490 X-1.0453 Y0.0497
N2491 X-1.0239 Y0.0339
N2492 X-1.0034 Y0.0169
N2493 X-0.984 Y-0.0012
N2494 X-0.9656 Y-0.0204
N2495 X-0.9483 Y-0.0407
N2496 X-0.9322 Y-0.0618
N2497 X-0.924 Y-0.0743
N2498 X-0.8673 Y-0.1676
N2499 X-0.84 Y-0.2079
N2500 X-0.8112 Y-0.2472
N2501 X-0.781 Y-0.2854
N2502 X-0.7494 Y-0.3225
N2503 X-0.7165 Y-0.3584
N2504 X-0.7098 Y-0.3658
N2505 X-0.6914 Y-0.3884
N2506 X-0.6744 Y-0.4121
N2507 X-0.6588 Y-0.4368
N2508 X-0.6569 Y-0.4402
N2509 X-0.6434 Y-0.4659
N2510 X-0.6316 Y-0.4924
N2511 X-0.6215 Y-0.5196
N2512 X-0.6132 Y-0.5475
N2513 X-0.6067 Y-0.5758
N2514 X-0.6021 Y-0.6044
N2515 X-0.5993 Y-0.6333
N2516 X-0.5984 Y-0.6624
N2517 X-0.5992 Y-0.6905
N2518 X-0.6019 Y-0.7186
N2519 X-0.6059 Y-0.7444
N2520 X-0.6059 Y-0.9429
N2521 G00 Z0.32
N2522 X-1.7494 Y-0.3014
N2523 Z-0.03
N2524 G01 X-1.5491 Y-0.3015 F180.
N2525 X-1.5472 Y-0.2842
N2526 X-1.5431 Y-0.263
N2527 X-1.537 Y-0.2418
N2528 X-1.5244 Y-0.2111
N2529 X-1.5182 Y-0.1994
N2530 X-1.5049 Y-0.1782
N2531 X-1.4883 Y-0.157
N2532 X-1.4675 Y-0.1358
N2533 X-1.4395 Y-0.114
N2534 X-1.4183 Y-0.1012
N2535 X-1.4024 Y-0.0934
N2536 X-1.3759 Y-0.0832
N2537 X-1.3547 Y-0.0775
N2538 X-1.3335 Y-0.0737
N2539 X-1.3123 Y-0.0717
N2540 X-1.2806 Y-0.0722
N2541 X-1.2487 Y-0.0767
N2542 X-1.2275 Y-0.0821
N2543 X-1.2063 Y-0.0896
N2544 X-1.1851 Y-0.0993
N2545 X-1.1594 Y-0.1146
N2546 X-1.1427 Y-0.127
N2547 X-1.1324 Y-0.1358
N2548 X-1.1115 Y-0.157
N2549 X-1.0949 Y-0.1782
N2550 X-1.0367 Y-0.274
N2551 X-1.0155 Y-0.3059
N2552 X-0.9859 Y-0.3478
N2553 X-0.9537 Y-0.3902
N2554 X-0.9307 Y-0.4185
N2555 X-0.9003 Y-0.4538
N2556 X-0.8614 Y-0.4963
N2557 X-0.8458 Y-0.5156
N2558 X-0.8309 Y-0.5387
N2559 X-0.8201 Y-0.5599
N2560 X-0.8117 Y-0.5811
N2561 X-0.8055 Y-0.6023
N2562 X-0.8012 Y-0.6235
N2563 X-0.7987 Y-0.6447
N2564 X-0.7981 Y-0.6659
N2565 X-0.7993 Y-0.6871
N2566 X-0.8024 Y-0.7083
N2567 X-0.8073 Y-0.7295
N2568 X-0.8122 Y-0.7444
N2569 X-0.6974 Y-0.9429
N2570 G00 Z0.2
N2571 Z1.
N2572
N2573 M05
N2574
N2575 M30
%00001
Re: Fagor 8020ms with Windnc
Hi Arron,
Those Error 34 Strange Character codes can be caused by many different things. It's like a "catch all" code for errors that Fagor doesn't have any other error code for.
Anyway, when I get one of those codes the things I check are:
1. Does the name of the program match the line 1 number (without the %sign). The five numbers after the % in line one must match the name of the program.
2. If you have any comment lines - anything inside of parenthesis () - don't use odd characters. Keep it to simple alphanumeric code.
3. Make sure your line numbers are in numerical order. You can number by 1, 2's, 5's or 10's or whatever
(for example:
010 xxxxxx
020 yyyyyy
030 zzzzzz
etc.
- but, no matter how many numbers you skip, they just HAVE TO BE in numerical order.
(BTW, I recommend you set your CAM software up to go by tens.)
4. I don't think you can have any lines without anything in them (no blank lines) - check your last several lines of code.
5. I don't think that you can have a decimal point in a federate (F) statement - so get rid of all your "F180." and change them to "F180"
Try those things and see if you get better results.
R/Todd
Re: Fagor 8020ms with Windnc
I have made all the adjustments you suggested and I am still having some troubles. When I try to transfer the file to the control via windnc I now either get the strange character or invalid file name error. These seem to be the two errors that im getting hung up on. No matter how many different codes I try I get these same two error messages. Is there any chance you happen to have a small sample code that you know works on the 8020 that I could reference to try and figure out my post processor?
Re: Fagor 8020ms with Windnc
Hi Arron,
Sure. Here is a small program that I have for the Fagor 8025M. It should load on your F8020 machine.
Don't try an run it though - this is for a 4ft x 8ft router. So, some of the X & Y numbers are pretty large.
%51059
N0010 (WCF59&60-Router.pim)
N0020 (Fagor 8025M MotionMaster Router_2012-02-09.scpost)
N0030 (12/01/2013)
N0040 G0 G17 G40 G44 G70 G80 G90
N0050 G59 X0 Y0 Z0
N0060 G53 X0 Y0 Z0
N0070 G54 X0 Y0 Z0
N0080 G54
N0090 (WCF59&60-Router)
N0100 (Drill, HOLE_POINTS, T1: Drill, 0.125 in diameter, 0.78 in Deep)
N0110 (Drill, 0.125 in diameter)
N0120 G90
N0130 T1.1
N0140 M6
N0150 G43 T1.1
N0160 G54
N0170 G0 Z0.3937
N0180 S1000 M3
N0190 G4K5
N0200 G83 G98 G1 X7.7850 Y2.0450 Z0.0197 I-0.1999 J4 F4
N0210 G0 X7.5037 Y0.3750
N0220 G0 X6.0350
N0230 G0 X4.5350
N0240 G0 X3.0350
N0250 G0 X1.4100
N0260 G0 X1.7850 Y2.0450
N0270 G0 Y8.0450
N0280 G0 X1.2850 Y9.5450
N0290 G0 X2.7850
N0300 G0 X4.2850
N0310 G0 X5.7850
N0320 G0 X7.2850
N0330 G0 X8.7177
N0340 G0 X7.7850 Y8.0450
N0350 G0 X11.7160 Y7.8750
N0360 G0 X11.9972 Y9.5450
N0370 G0 X13.4660
N0380 G0 X14.9660
N0390 G0 X16.4660
N0400 G0 X18.0910
N0410 G0 X17.7160 Y7.8750
N0420 G0 Y1.8750
N0430 G0 X18.2160 Y0.3750
N0440 G0 X16.7160
N0450 G0 X15.2160
N0460 G0 X13.7160
N0470 G0 X12.2160
N0480 G0 X10.7833
N0490 G0 X11.7160 Y1.8750
N0500 G80
N0510 (Outside Offset, WCF59_60, T4: Mill/router, 0.25 in diameter, 0.039 in Deep)
N0520 M5
N0530 (Mill/router, 0.25 in diameter)
N0540 G90
N0550 T4.4
N0560 M6
N0570 G43 T4.4
N0580 G54
N0590 G0 X11.7160 Y1.8750 Z0.3937
N0600 S400 M3
N0610 G4K5
N0620 X4.7850 Y2.9200
N0630 Z0.0197
N0640 G1 Z0.000 F4
N0650 Y2.6700 Z-0.022
N0660 G3 X4.9806 Y2.6781 I-0.0000 J2.3750 F4
N0670 G2 X4.7850 Y2.6700 I-0.1956 J2.3669 F10
N0680 G3 X6.5518 Y3.4578 I-0.0000 J2.3750
N0690 X4.7850 Y2.6700 I-1.7668 J1.5872
N0700 G1 Y2.9200 Z-0.039 F10
N0710 G0 Z0.3937
N0720 X14.7160 Y2.7500
N0730 Z0.0197
N0740 G1 Z0.000 F4
N0750 Y2.5000 Z-0.022
N0760 G3 X14.9116 Y2.5081 I0.0000 J2.3750 F4
N0770 G2 X14.7160 Y2.5000 I-0.1956 J2.3669 F10
N0780 G3 X14.7160 Y2.5000 I0.0000 J2.3750
N0790 G1 Y2.7500 Z-0.039 F10
N0800 G0 Z0.3937
N0810 X8.4083 Y-0.3115
N0820 Z0.0197
N0830 G1 Z0.000 F4
N0840 X8.2418 Y-0.1250 Z-0.022
N0850 X8.1301 Z-0.032
N0860 X8.0460 Z-0.039
N0870 X8.1301 F10
N0880 X8.2418
N0890 X8.1301
N0900 X0.9070
N0910 G2 X0.7820 Y0.0000 I0.0000 J0.1250 F10
N0920 G1 Y1.6700 F10
N0930 X-0.0000
N0940 G2 X-0.1250 Y1.7950 I0.0000 J0.1250 F10
N0950 G1 Y9.0000 F10
N0960 G2 X-0.0000 Y9.1250 I0.1250 J0.0000 F10
N0970 G1 X0.7820 F10
N0980 Y9.9200
N0990 G2 X0.9070 Y10.0450 I0.1250 J0.0000 F10
N1000 G1 X9.0975 F10
N1010 G2 X9.2225 Y9.9200 I0.0000 J-0.1250 F10
N1020 G1 Y9.1241 F10
N1030 X10.0798 Y9.0342
N1040 G2 X10.1910 Y8.8958 I-0.0130 J-0.1243 F10
N1050 G1 X9.3493 Y1.4764 F10
N1060 G2 X9.2121 Y1.3661 I-0.1242 J0.0141 F10
N1070 G1 X8.4203 Y1.4492 F10
N1080 X8.2543 Y-0.0141
N1090 X8.2418 Y-0.1250
N1100 X8.4083 Y-0.3115
N1110 G0 Z0.3937
N1120 X18.8958 Y-0.3018
N1130 Z0.0197
N1140 G1 Z0.000 F4
N1150 X18.7190 Y-0.1250 Z-0.022
N1160 X18.5940 Z-0.033
N1170 X18.5232 Z-0.039
N1180 X18.5940 F10
N1190 X18.7190
N1200 X18.5940
N1210 X10.4035
N1220 G2 X10.2785 Y0.0000 I0.0000 J0.1250 F10
N1230 G1 Y0.7959 F10
N1240 X9.4212 Y0.8858
N1250 G2 X9.3100 Y1.0242 I0.0130 J0.1243 F10
N1260 G1 X10.1517 Y8.4436 F10
N1270 G2 X10.2889 Y8.5539 I0.1242 J-0.0141 F10
N1280 G1 X11.0807 Y8.4708 F10
N1290 X11.2467 Y9.9341
N1300 G2 X11.3709 Y10.0450 I0.1242 J-0.0141 F10
N1310 G1 X18.5940 F10
N1320 G2 X18.7190 Y9.9200 I0.0000 J-0.1250 F10
N1330 G1 Y8.2500 F10
N1340 X19.5010
N1350 G2 X19.6260 Y8.1250 I0.0000 J-0.1250 F10
N1360 G1 Y0.9200 F10
N1370 G2 X19.5010 Y0.7950 I-0.1250 J0.0000 F10
N1380 G1 X18.7190 F10
N1390 Y0.0000
N1400 Y-0.1250
N1410 X18.8958 Y-0.3018
N1420 G0 Z0.3937
N1430 M5
N1440 G53
N1450 G0 Z5
N1460 X35 Y30
N1470 M30
I had a little more time to scan your Gcode above. Here are some other things to check:
1. Does your machine have a tool changer? If it does NOT - then the control will not understand line 2 (T codes are used to change tools).
2. Lines 6 & 9 are also blank lines (maybe you already got those deleted out).
3. There should not be a %0001 at the end of the file. The last line of code should just be: N2535 M30
4. Make sure that the file you are sending is a .PIM file. If you are editing this file with an editor like Notepad (or other word processor) it will sometimes change the file type to something besides .PIM. It has to be a .PIM file for the control to read it. The best way to edit these files to use Notepad, then make sure to hit the "File Save" and save the file BEFORE you hit the exit or close buttons. This way, Notepad will save it as the same file type as it was when it opened the file.
What kind of machine is this, Arron? It looks like the machine has a spindle, but this Gcode is pretty simple code. It's just a bunch of LITTLE short line segments with some small Z moves here and there (most of which are redundant).
What CAM software are you using? It looks like it is not very good CAM software. It looks like circles are being approximated by lots of little, tiny line segments instead of writing a G02 or a G03 statement. If this was a plasma torch, then the lots of little tiny line segments would be OK. But, if you are using this as a router or mill, your work will come out looking like lots of little tiny line segments. It is also putting in A LOT of redundant Z moves. For example:
N7 Z0.2
N8 Z0.1 (This is redundant)
N10 G01 Y-1.2512 F180.
N11 X-1.4942 Y-1.2435
N12 X-1.5289 Y-1.2267
N13 X-1.5627 Y-1.2083
N14 X-1.5955 Y-1.1882
N15 X-1.6273 Y-1.1665
N16 X-1.658 Y-1.1433
N17 X-1.6875 Y-1.1186
N18 X-1.7157 Y-1.0924
N19 X-1.7424 Y-1.0651
N20 X-1.9341 Y-1.1169
N21 G00 Z0.1 (This is again redundant - Z is already at 0.1)
N22 Z0.2 (This is also redundant - it should just go straight to Z0.2)
N23 X1.9344 Y-1.1159
N24 Z-0.25 (This is dangerous. You're crashing your spindle from Z0.2 down to Z-.25 at RAPID [G00] speed!!!!!)
(of course this assumes that Z0 is the top of the part)
Was your CAM software ever tailored for your machine? It has to be. There are a whole bunch of "Parameters" that are "set" to particular values in the F8020 control. The Gcode that is created by the CAM software has to be made to "match" your parameter settings. If it is not, then the Gcode will not "fit" your machine control and the CAM software will write things in the Gcode that the control will not understand. It looks to me like that might be happening here.
Tell me more about this machine (answer questions above) and I might be able to help get you running.
Here is a recap of questions:
1. Does this machine have a tool changer?
2. What kind of machine is this? (e.g. router, mill, plasma, etc.)
3. What CAM software is this?
4. Has it been tailored for your machine?
R/Todd
Re: Fagor 8020ms with Windnc
The machine is a 1989 NASA II Mill. It has two spindles but I have been focusing on just getting one up and running for now. I am using BobCAD for my cam. They told me the postprocessor they generated for the 8025 is good. I have strongly suggested they take a look at what they consider to be good since I have had nothing but issues using it. The cam nor the post processor has been set up specifically for my machine. They told me they would generate a post for my mill but I would have to provide them with the list of G and M codes and a functioning G code that currently works on my machine. The G and M code list is easily obtained but the functioning G code sample is where I am having trouble. I have two other routers and a 3D printer that I have been using for several years but those all use Mach3 or other proprietary software and I have never had to mess with any G code or post processors. This whole process is very new to me. I have tried my best to try and solve the issues on my own but I have finally had to admit defeat and seek help. Are you capable of generating a postprocessor for me. I would be happy to pay for your services if this is an option. I am attempting to get in touch with the first owner of the machine to see if they still have any other their old codes as well. I think this might help the process of getting this thing running.
Re: Fagor 8020ms with Windnc
OK. That helps a bit.
Well, the first problem is BobCAD. I use BobCAD for my CAD software - but that is it. Dealing with BobCAD-CAM beyond that is frustrating and useless - at BEST!
I use SheetCAM for my CAM software. It is designed for sheet cutting with Plasma and routers - but it will work for the 2.5D CAM needed for a 3 axis mill (well most functions anyway).
BobCAD is correct that an F8025M post processor should work for the F8020M control.
Really, all the BobCAD folks need to have is a programming manual for the F8020M or F8025M. If you can provide them with a .pdf copy of the manual, then THAT is what they should be tailoring the post processor from - NOT some "working" Gcode from some friend of a friend that has a machine like this in his basement, yatta, yatta. Those manuals are available online. Just google "Fagor 8020 manuals" and do some digging and you'll find them. They used to be on Fagor's website - but I haven't looked lately.
WIth all of that being said, that looks like an interesting machine. I found one picture of that machine on a google search. Nice looking machine. I've never dealt with a 2 spindle machine. But, I do know that there is at least one parameter setting that deals with that in the F8020/25 control. If you are trying to get just one spindle to operate - you need to go into the parameter list and find out the correct settings for which parameters to make that a single spindle machine. Chances are good that the F8020 control needs to see something in the Gcode that it is not seeing since you are trying to put Gcode into the control that is written for a single spindle and the control is looking for Gcode that "talks" to 2 spindles at the same time. BTW - be sure to back up ALL your parameter settings before you make any changes - that way you'll have them for reference when you want to change them back to double spindle operations.
The most sure-fire way of having a fail-proof and fool-proof backup of your parameters is to page thru all of them, one page at a time and take a digital picture of the screen. Then, put them all in a folder on a computer somewhere. Then put them all in another computer somewhere else. And, just to be sure, put them on a laptop somewhere else. That way, you'll always have access to the parameters that need to be set for that machine in case the battery backup goes dead (it happens all the time - just search this forum to see how many folks get caught with a dead battery and no parameter backups). Please do yourself a favor and back up the parameters right now.
In order to get "apples" to "apples" here, you'll need to send "single spindle code" to the machine that has parameters set for "single spindle"; or, you'll need to get the CAM software set up to write "double spindle" Gcode to send to an F8020 control that has parameters set up for (wants to see) "double spindle" Gcode. I hope that analogy makes sense.
I would do as you are thinking. Set up the parameters in the control for single spindle operation. Then start out with CAM software that is tailored for this machine in single spindle operation. Once you get that going, you'll have had time to learn what you need to do in order to get CAM software to write "double spindle" Gcode. BTW - I don't even know what "double spindle" Gcode looks like - but I know that somehow it has to be different from the code for normal, everyday, single spindle Gcode. I do remember that it is discussed in the Fagor manuals, you'll have to get into the manuals and figure that out - later.
Moving on to the task at hand. The Gcode I sent in the last post, is valid Gcode for the F8025M. So, that should help with the BobCAD guys, if you want to get them to write the post processor.
So, here's what I see you needing to accomplish:
1. Back up your machine parameters.
2. Set the parameters in the machine for single spindle operations. To do this, get ahold of the F8020M (or F8025M) OEM manual. That's the manual that will have the list of parameters and how to set them for the machine that your OEM (NASA installed the control on).
3. Write some really basic Gcode (from scratch, i.e. write it by hand not from a CAM program) to use as I test program to get the machine moving. Just do X, Y & Z moves at first. Once you get that working, then add a spindle Gcode to get the spindle turning. Then, if that goes well, combine all 3 together.
4. While you are working on step 2. above, get BobCAD busy on writing (or fixing) the post processor for your CAM portion of BobCAD-CAM software.
5. Use the machine for a while in single spindle configuration. Make some parts, try different things to get familiar with creating code for the machine to do various types of machining (e.g. profiles cuts, hole drills, pockets, bosses, etc.).
6. While you are doing step 5 above, begin researching double spindle operations. Learn how the Gcode is different. Then get BobCAD-CAM working on tweaking the post processor to handle the multi spindle code.
7. Go back and change the F8020 parameters for multi spindle operations.
8. Repeat the applicable steps above for double spindle operations.
Writing Gcode from scratch is not that difficult for basic shapes like squares, triangles, and even circles. You seem like a pretty smart fella and should be able to do it once you've learned the basic G, M, S and T commands. Consider taking a few days to learn the basics and then dig into the F8020/F8025 programming manuals. You'll pick it up pretty fast. Unless you're programming French curves or some kind of crazy splines it's pretty straightforward if you understand an X,Y & Z coordinate system.
Let me know if you have any additional questions.
Sounds like a fun project you have there. I'm sure you can get it working for you soon - with a little help from your friends.
R/Todd
Re: Fagor 8020ms with Windnc
BTW, here is a very simple program to try to load onto the control, just to see if it will load and to try to move the machine.
%00011
N0010 (THIS IS A SIMPLE PROGRAM)
N0020 (09-30-2014)
N0030 G0 G17 G40 G44 G70 G80 G90
N0040 G0 Z1
N0045 G1 Z0.5 F10
N0050 G0 X0 Y0
N0060 G1 X2 F10
N0070 Y2
N0080 X0
N0090 Y0
N0100 G0 Z1
N0110 M30
This program just moves the spindle up to Z1 at rapid (G0) speed. Then runs the spindle down at F10 (10ipm) to Z0.5. Then the table moves (at F10) in a 2 inch square box profile from X0Y0 to X2Y0 to X2Y2 to X0Y2 and back to X0Y0. Then it rapids the spindle back up to Z1.
I'm not sure of your skill level here Arron, so please don't be offended if I am over simplifying things for you.
So, here's how to load this program into the control after you've set it up for single spindle ops.
1. Copy and paste the program above into a .PIM file. (Make a copy of an existing .PIM file, then cut and paste the above into it).
2. Make sure to remove any blank characters in every line (no blank spaces at end of each line).
3. Select "File Save" and then close the file.
4. Turn on the machine.
5. Do a machine home operation.
6. Do a touch-off so that Z0 is about 1" above the mill table.
7. Fire up the computer and WinDNC and send the file to the control.
8. If the file is successfully sent then go to "OP MODE -> 0"
9. Pull up the file (push P00011 -> recall)
10. When the program loads, select CYCLE START. Keep your hand close to the E-stop button in case something bad wants to happen.
Let me know how that goes.
If that code runs, we'll add some spindle Gcode.
R/Todd
PS - send me a PM with your email address. I can email you some files that might help with all this stuff.
Re: Fagor 8020ms with Windnc
I am starting to realize that BobCad was not the best choice in the world but fortunately I did not pay that much for version 26. I don't know if they were desperate to sell a seat or just didn't care but I only forked out $300 for a new license and a year of support. I also have a license for Inventor Pro that I use for my CAD software. I love it! It doesn't get any easier than Inventor in my opinion. With that being said, is it not such a thing that once I have the post processor figured out it will just be a post and go type of thing? Meaning, no matter what the part is that I designed in inventor, weather it be a simple bushing or a complicated 3D part, with the correct post processor all I have to do is design that part and click generate post or am I going to have to modify the post for every type of part?
Re: Fagor 8020ms with Windnc
I assure you that you cant offend my by over simplifying things, This is one of those things were until I get it figured out, the more dumbed down you can make it the better off ill be.
Re: Fagor 8020ms with Windnc
No, once you get the post processor set up for the type of operations you want to do (like single spindle first), then you can just feed drawings into it and the code should come out ready to run. Although, I always look the code over (manually - for lack of a better term) just to have a "reality check," This helps to make sure I don't have some bugged up code and can prevent crashing the machine.
As I remember, BobCAD has a webpage to go to where you can modify your post processor as you need to get it tweaked for your machine. I haven't looked at that in a long time and not sure if they still offer that. I'm still on V24 and don't think I'll upgrade any time soon.
The code that you posted first looks really "buggy." But, if you get that sorted out - you should be able to CAM out your parts pretty reliably for that NASA II machine.
BTW - do you have the manuals for the F8025M? If not, you can download them all from here:
:: FAGOR AUTOMATION ::
I did a complete re-build of a similar mill for a buddy of mine that also has a F8025MS control. You can read some of it here:
http://www.cnczone.com/forums/fagor-...-hardware.html
I never got around to finishing that thread, but I got the machine running really well for him. He's making parts with it every day.
You'll get there too. It'll just take a little effort.
R/Todd
Re: Fagor 8020ms with Windnc
Quote:
Todd, I was so excited to test out your sample code that I ran down here to the shop, fired up the mill and loaded the code. IT WORKED! I was so excited to see it load and move in that little square. I went ahead and added an M03 and M05 to the code and it worked first time. Spindle fired up, it did its square movement, the spindle shut down and it went back to zero. My question now is what's the next step?
Awesome Arron! I'm glad that worked and got the machine moving.
The next step is to do what you were already seeking...... getting a post processor that writes out Gcode that the control can understand.
I would pursue that in a couple of directions.
First, give me a few days and I will search around for a BobCAD post processor that I wrote for my V23 a while back (quite a while). At one point I had tweaked the post processor and got BobCAM sptting out fairly reliable code for the F8025M. I just have to refresh my memory on how to do all that and see if I can find the post processor that I finally came up with. That PP would do most simple functions you need to do, such as most G functions, M functions, S functions and even a T function for doing tool changes on my router (which I don't think you'll need or want). That will get you up and running and able to make parts with one spindle. That PP that I had made is not set up for complex things like canned cycles, rigid tapping and things like that. But, for just cutting out fairly simple parts, it will work fine. In a couple days I'm heading out on the road for 10 days for work (my actual day-job that pays the bills). I will have time to play with this stuff then and get back to you with more info.
Second, in conjunction with the above, start hitting up (and keep after) BobCAD-CAM (BCC) to write you a customized PP for that machine. It will take a lot of frustrating calls to tech support and sending them whatever they ask for, but you've paid for that service and they should do it for you. You need to bug them to get the PP capable of doing more complex tasks like what I mentioned above. Also, if those spindles have two different speed ranges, the PP code should be written to handle that too. It will take a while and it will probably get done in increments (when you go to do something new on the machine some day and find out that the PP is not putting out the correct Gcode - you'll have to get them to tweak the PP again, etc.) So, your PP is something that can evolve over time as you try to do more and more complex operations, etc.
Then, start researching info on using a machine with two spindles. Learn more about programming with two spindles, and what the Gcode should look like, etc. You know, I just looked through the F8025M OEM manual and I didn't see anything about multiple spindles. This thing might be a lot simpler than I'm envisioning. When you ran the M03 and the M05, did both spindles do the same thing? They are probably just set up for both spindles to do the same thing (same speed, etc.) using just the standard single spindle Gcode. That makes since, given that the whole purpose for a second spindle is just to double your production rate. This may not be such a big thing after all. Not sure. We'll have to research that.
Also, in the mean time, if you have any particular part that you need to start making you can send me the CAD drawing and I will CAM it out in SheetCAM and you can use that Gcode to get rolling.
Glad you got the machine moving. Let me know if the machine has a tool changer and about the spindles operating together.
R/Todd
BTW - if you can still go back and edit your original post, you can take out most of that code that you posted there. Just leave the first and last 20 lines or so. ;-)