Heidenhain "Angle Reference Missing" error
Hi all, I've just loaded a program into an old Bridgeport Interact 412 running Heidenhain TNC 151, that I created using Mastercam.
I've come across an error while trying to do a 26x6mm slot, using a 6mm cutter (set to 5.98mm diameter). When it gets to line 54 I'm met with the error "Angle Reference Missing".
40 TOOL CALL 3 Z S3500
41 M6
42 L X+80.950 Y-0.010 R0 F9999 M03
43 L Z+10.000 R0 F9999 M8
44 L Z+2.000 R0 F9999
45 L Z+0.000 R0 F100
46 L X+90.000 Z-0.474 R0 F200
47 L X+90.007 Y-0.007 R0 F200
48 L X+90.010 Y+0.000 Z-0.475 R0 F200
49 L X+90.007 Y+0.007 R0 F200
50 L X+90.000 Y+0.010 Z-0.476 R0 F200
51 L X+80.000 Z-1.000 R0 F200
52 L X+70.000 R0 F200
53 CC IX+0.000 IY-0.010
54 C X+69.990 Y+0.000 DR+ R0 F200
55 CC IX+0.010 IY+0.000
56 C X+70.000 Y-0.010 DR+ R0 F200
57 L X+90.000 R0 F200
58 CC IX+0.000 IY+0.010
59 C X+90.010 Y+0.000 DR+ R0 F200
60 CC IX-0.010 IY+0.000
61 C X+90.000 Y+0.010 DR+ R0 F200
62 L X+80.000 R0 F200
63 L Z+10.000 R0 F9999
64 M9
65 M05
I'm not too familiar with Heidenhain programming to be able to see what's wrong, any programs are made using Mastercam and I'm used to Fanuc :o.
Can anyone shed any light on this for me please? Is it because the cutter rad is so close to the slot rad?
Re: Heidenhain "Angle Reference Missing" error
Quote:
Originally Posted by
Lugy
Hi all, I've just loaded a program into an old Bridgeport Interact 412 running Heidenhain TNC 151, that I created using Mastercam.
I've come across an error while trying to do a 26x6mm slot, using a 6mm cutter (set to 5.98mm diameter). When it gets to line 54 I'm met with the error "Angle Reference Missing".
40 TOOL CALL 3 Z S3500
41 M6
42 L X+80.950 Y-0.010 R0 F9999 M03
43 L Z+10.000 R0 F9999 M8
44 L Z+2.000 R0 F9999
45 L Z+0.000 R0 F100
46 L X+90.000 Z-0.474 R0 F200
47 L X+90.007 Y-0.007 R0 F200
48 L X+90.010 Y+0.000 Z-0.475 R0 F200
49 L X+90.007 Y+0.007 R0 F200
50 L X+90.000 Y+0.010 Z-0.476 R0 F200
51 L X+80.000 Z-1.000 R0 F200
52 L X+70.000 R0 F200
53 CC IX+0.000 IY-0.010
54 C X+69.990 Y+0.000 DR+ R0 F200
55 CC IX+0.010 IY+0.000
56 C X+70.000 Y-0.010 DR+ R0 F200
57 L X+90.000 R0 F200
58 CC IX+0.000 IY+0.010
59 C X+90.010 Y+0.000 DR+ R0 F200
60 CC IX-0.010 IY+0.000
61 C X+90.000 Y+0.010 DR+ R0 F200
62 L X+80.000 R0 F200
63 L Z+10.000 R0 F9999
64 M9
65 M05
I'm not too familiar with Heidenhain programming to be able to see what's wrong, any programs are made using Mastercam and I'm used to Fanuc :o.
Can anyone shed any light on this for me please? Is it because the cutter rad is so close to the slot rad?
Hi Lugy,
Did you manage to find a solution to this problem?
I am having a similar problem; it stops at line 140 (code is below) with same error/warning message: "Angle Reference Missing". Any help would be appreciated
Shumail
134 L X+57.159 Y+52.428
135 L X+52.258 Y+51.337
136 L X+45.076 Y+49.609
137 L X+42.456 Y+48.944
138 L X+40.005 Y+48.383
139 CC X+21.810 Y+119.199
140 C X+30.496 Y+46.601 DR-
141 CC X+30.497 Y+46.586
142 C X+30.496 Y+46.571 DR+
143 L X+34.491 Y+45.911
144 L X+38.167 Y+45.106
145 L X+49.195 Y+42.341
146 L X+52.258 Y+41.604
147 CC X+84.256 Y+173.158
148 C X+62.673 Y+39.499 DR+
149 CC X+83.734 Y+184.622
150 C X+73.088 Y+38.366 DR+
151 CC X+87.799 Y+223.863
152 C X+76.082 Y+38.153 DR+
153 CC X+76.157 Y+39.338
154 C X+77.151 Y+39.988 DR+
155 L X+75.446 Y+42.595
156 CC X+76.440 Y+43.245
157 C X+76.523 Y+44.429 DR-