584,874 active members*
4,968 visitors online*
Register for free
Login
IndustryArena Forum > MetalWorking > MetalWork Discussion > CAD drawings of most popular V8 engine bellhousing patterns
Page 1 of 5 123
Results 1 to 20 of 87
  1. #1
    Join Date
    Jan 2006
    Posts
    481

    CAD drawings of most popular V8 engine bellhousing patterns

    CAD drawings of most popular V8 engine bellhousing patterns

    Hi

    Does anyone have CAD drawings of most popular engine bell housing patterns that you wouldn't mind sharing

    Ford Modular V8 bellhousing patterns detailed drawings or dimensions ?
    Ford 460 big Block ?
    Ford 351 cleveland ?

    chevrolet big block / small block ?

    chrysler big block / small block ?

    Even raw G-code would be fine.

    would be greatly appreciated

    cheers

  2. #2
    y.not Guest

    chevy bell drawing pattern

    hi, have chevy SB,BB drawings. will send to your email - just send me a link. radim [email protected]
    p.s. have you found mopar bell pattern ? i can not find it anywhere .... thanks ....

  3. #3
    Join Date
    May 2008
    Posts
    12
    Sad (being a Ford fan) that the only patterns we can find are the Chevy patterns.

    I'm looking for the Ford small block and the Buick/Rover aluminum V8 patterns.

    Add me to the list of those looking for bell housing patterns.

    UPDATE!

    Yesterday I put the measurements for the small block in AutoCad.

    Now that I looked at the pictures of the 60 degree V6, small block and the big block V8 blueprints, they are showing the exact same measurements as the small block (the measurement were in a different order so they are not the same prints recopied).

    Of the pictures that I have downloaded, were they mistakenly showing the small block rear prints mislabeled as the V6 and Big Block V8?

    If so, I would like to get a copy of the Big Block V8 as well.

    I will make a note of posting any others that I find here as well.

  4. #4
    Join Date
    May 2008
    Posts
    12
    And a couple hours later I scored the Ford patterns on line!

    I have them all posted here, but will e mail them to anyone interested if needed.

    I have listed the Chevy and ford patters I have found so far.

    http://s911.photobucket.com/home/archangel2003/index

  5. #5
    Join Date
    Feb 2008
    Posts
    14
    The 90° V6, SBC, and BBC have the same bellhousing pattern. The 2 Chevy V8's also shared the same flywheel pattern until 1985. The 85 and newer small block flywheel changed with the addition of the one piece rear seal. The 84 and older V6 may also have been the same but I never looked into it.

    Great stuff. I actually measured a BBC head gasket to come up with the bolt pattern for a project I was working on. I was very close with my numbers. Wish I had found this thread before I started though.

  6. #6
    Join Date
    Jan 2007
    Posts
    6

    hey Guys
    Can i get the SB/BB Ford Drawings
    Thanks

  7. #7
    Join Date
    May 2008
    Posts
    12
    How did you miss post number 4?

    You were only post number 6, so the total before you posted was 5.


    Quote Originally Posted by archangel View Post
    And a couple hours later I scored the Ford patterns on line!

    I have them all posted here, but will e mail them to anyone interested if needed.

    I have listed the Chevy and ford patters I have found so far.

    http://s911.photobucket.com/home/archangel2003/index
    The Photobucket link above still works as of 6:30 am 20 January 2010.

  8. #8
    Join Date
    Jan 2010
    Posts
    2

    duratec v6

    I would love to have those specs for the ford v6 duratec family of engines, does anyone have them or know where to get them, and some audi bellhousing patterns would be great as well.

  9. #9
    Join Date
    May 2008
    Posts
    12
    Quote Originally Posted by heythere2581 View Post
    I would love to have those specs for the ford v6 duratec family of engines, does anyone have them or know where to get them, and some audi bellhousing patterns would be great as well.
    Check here.

    They list some Audi and VW's

    http://www.nexustech.ca/chimaera/Not...ine_Trans.html

  10. #10
    Join Date
    Jan 2006
    Posts
    481
    LOL i'm a ford orientated person also most information is chevy chevy chevy !!!!! WOooooooooooooooooo this is great news some patterns starting to appear.


    Does anyone have BIG BLOCK FORD ? bellhousing bolt pattern they want to share????


    cheers

  11. #11
    Join Date
    Jul 2010
    Posts
    24

    I have some Mopar drawings

    I have both the small and big block Chrysler bellhousing drawings, plus the slant 6.

    I also have a really fuzzy photo of an AMC V8 blueprint, but it is readable!

    I also have some nice drawings of 4 and 5 cylinder Volkswagen TDI Diesels.

    PM me your email address and I'll send them to anyone who wants them, I'm not interested it setting up a photo hosting account.

    Lastly I'm searching for a BOP Buick/Olds/Pontiac/Cadillac bellhousing bolt pattern drawing.

    P.S. I have a spread sheet listing a pattern for the Mercedes OM617 5 cylinder Diesel

  12. #12
    Join Date
    May 2008
    Posts
    12
    freefuel
    I PM'd you for the info.:stickpoke

  13. #13
    Join Date
    Jul 2010
    Posts
    24
    Does anyone have a drawing of the flywheel bolt patterns for the early and late model Chevy V8, and the AMC engines too?

  14. #14
    Join Date
    Oct 2010
    Posts
    0

    Slant 6 Bellhousing Bolt Pattern

    From FREEFUEL
    Attached Thumbnails Attached Thumbnails slant6.jpg  

  15. #15
    Join Date
    May 2008
    Posts
    12
    I have the GM and Ford V8 patterns on my photo bucket account listed in this post.

    Would you, or anyone you know, happen to have the Buick 215/Rover 3.5 bell housing pattern measurements?

  16. #16
    Join Date
    Feb 2007
    Posts
    592

    Thanks for the links!

  17. #17
    Join Date
    Oct 2008
    Posts
    3

    Small block Chevy Block Front

    I am in dire need of the location of all the holes in the front of a Small Block Chevy.

    Any help would be great,,,,,,
    thanks.

  18. #18
    Join Date
    Mar 2004
    Posts
    47

    engine bolt patterns

    Please email me the files at [email protected]
    Bob S
    Robert Setree 502-452-9851

  19. #19
    Join Date
    Feb 2011
    Posts
    0

    bell housing and motor pattern needed

    I would greatly appreciate any drawings showing dimensions for a 3800v6 chevy or a 4l80E transmission. I want to make an adapter plate to pu the two together.

  20. #20
    Join Date
    Apr 2005
    Posts
    460

    Wink My Two cent's

    The BOP And Chev V8 share the same dowel location's and lower holes ,The GM Power book's have some of the V6 and V8 pattern's front and back the worst thing is some are metric and some are inch also the X&Y 0/0 is always somewhere other than the crank shaft center takes a bit of siffering to get there but it's doable as for the ford's small and 460 I think I have print's of as for the FE''390'' that's another hard one the Y block was a concern of mine a while back and that's another hard one to find . If you have the block and a surface plate and highth gage you can map it slow but work's or stand on end in a mill and probe the holes with a dowel pin and use the Digital to map it . some of the manufactures will help but in this day and age customer service at there level is like calling teck suport for anything electronic. archangel I'm not sure that the old 215 buick/old's and the rover have the same bellhousing? and free fuel the chevy flywheel's are semetrical so there a snap as for the AMC it has some stray's in it Response the 3800V6 front wheel drive has the same patern as the 3100V6 and it's in the GM power book I may have it drawn on another P.C. in bobcad and the 4L80 is chevV8 that adapter is avalible from ATI Kevin

Page 1 of 5 123

Similar Threads

  1. Popular presents.......
    By MarkusD in forum Portfolio Board
    Replies: 4
    Last Post: 02-13-2014, 01:29 PM
  2. What will I make Is the popular question...
    By milhead in forum CNC Wood Router Project Log
    Replies: 46
    Last Post: 02-08-2012, 12:40 AM
  3. Big Block Chev Bellhousing Dimensions
    By hellcycledoctor in forum Australia, New Zealand Club House
    Replies: 3
    Last Post: 03-30-2010, 11:27 PM
  4. drawing board drawings to cad drawings
    By mike hide in forum Uncategorised CAM Discussion
    Replies: 5
    Last Post: 03-23-2009, 10:35 AM
  5. single cylinder engine drawings?
    By savvypower in forum MetalWork Discussion
    Replies: 4
    Last Post: 02-01-2007, 12:44 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •